Skip to main content

Worldwide Shipping · Secure Payments

At a glance

This ir and rf transmitters and receivers is a good fit for makers, students and electronics hobbyists. Main specs: item type RF Wideband Amplifier; operating frequency (mhz) 0.1-2000; impedance (ω) 50Ω.

Key Highlights

  • Item Type: RF Wideband Amplifier
  • Operating Frequency (MHz): 0.1-2000
  • Impedance (Ω): 50Ω

Ideal For

  • Everyday use

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeRF Wideband Amplifier
Operating Frequency (MHz)0.1-2000
Impedance (Ω)50Ω
End Connector genderSMA-Female
PCB ColorGreen + Gold
Dimensions (L x W x H) mm52 x 25 x 6
Weight (g)5
Shipping Weight0.01 kg
Shipping Dimensions14 × 10 × 8 cm

Overview

The 0.1-2000mhz RF Wideband Amplifier Gain 30db Low-Noise Amplifier LNA Board Module is listed in our ir and rf transmitters and receivers range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: RF Wideband Amplifier (your supply must deliver at least this much current)
  • Operating Frequency (MHz): 0.1-2000 (make sure the rest of your system works at this frequency)
  • Impedance (Ω): 50Ω
  • End Connector gender: SMA-Female (confirm your cable or board uses the same connector)
  • PCB Color: Green + Gold
  • Dimensions (L x W x H) mm: 52 x 25 x 6 (measure your mounting space before ordering)
  • Weight (g): 5 (important for drones, RC models and anything you carry)
  • Shipping Weight: 0.01 kg (important for drones, RC models and anything you carry)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

0.1-2000mhz RF Wideband Amplifier Gain 30db Low-Noise Amplifier LNA Board Module can be applied to various RF receive front-end and increases the communication distance. It is widely used for Short wave, FM radio, remote control receiver, such as cable TV signal amplifier need low noise RF signal amplification
Operating Tips:
1. Amplifier working frequency of the lower limit is subject to input and output capacitor, the default value is 0.1 uF, working to 0.1 MHz. 2. Increase the input and output capacitance appropriately, can extend the cut-off frequency, such as 10uF capacitance can work to 5KHz. 3. When the power supply voltage changes in 5V-8V, it can be used as a variable gain amplifier, gain increases with the increase of the power supply voltage, which suitable for radio frequency receive front-end circuit, using DA control power supply voltage, to control the gain of the amplifier, automatic gain control. 4. When the power supply voltage in 8V-10V, the low-frequency end gain up to 30 dB, at this time the amplifier has a low noise coefficient and good stability. 5. When the voltage is 12V, reach maximum gain, the low-frequency end gain of 32.5 dB. Note : On product 0.1 - 3000Mhz printed working remains same.

Features:

  1. This product with wide frequency range, high gain, low noise figure.
  2. This product can be applied to various RF receive front-end and increases communication distance.
  3. When the working frequency is less than 500 MHZ, it gets well gain flatness, can make it less than 1dB after careful adjustment.
  4. The lower the frequency, the higher gain consistency.
  5. Used for short wave, FM radio, remote control receiver, such as cable TV signal amplifier need low noise RF signal amplification.

Package Includes:

1 x 0.1-2000mhz RF Wideband Amplifier Gain 30db Low-Noise Amplifier LNA Board Module

Quick specs

Item Type
RF Wideband Amplifier
Operating Frequency (MHz)
0.1-2000
Impedance (Ω)
50Ω
End Connector gender
SMA-Female
PCB Color
Green + Gold
Dimensions (L x W x H) mm
52 x 25 x 6
See all specifications