Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 15 cm RG1.13 coax pigtail with an SMA female jack on one end and a stripped, tinned shield tail on the other. It lets you solder an SMA connection directly onto a board, terminal block or custom antenna feed.

Key Highlights

  • 15 cm RG1.13 coax with SMA female jack on one end
  • Opposite end stripped and peeled with shield separated and tinned
  • Compact 11 mm SMA connector body for tight spaces
  • 50 Ohm RF impedance for WiFi, GSM, LTE and 433 MHz work
  • Lightweight 5 g shipping weight, easy to include in builds
  • Useful for custom antenna feeds and board-level repairs

Ideal For

  • RF hobbyists soldering custom antenna feeds
  • Repair technicians replacing short internal coax leads
  • Makers building GSM, LTE or 433 MHz devices
  • Radio astronomy and machine-to-machine experimenters
  • Anyone needing a compact SMA female pigtail

Buying Tip

Confirm that your device or antenna uses a standard SMA male plug, not RP-SMA, before soldering the stripped end into place.

Elecvora expert review

Our verdict

A practical little pigtail for anyone who needs an SMA female connection soldered into a tight space. The prepared stripping head removes the fiddliest part of the job, though the unfinished end demands careful soldering.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Solder-ready stripped and tinned tail
  • Compact 11 mm SMA body
  • Flexible RG1.13 coax
  • Lightweight and easy to route

Cons

  • Tail end requires soldering skill
  • Standard SMA only, not RP-SMA
  • Short 15 cm length limits reach

Best for

Compact custom RF and antenna wiring projects

Not ideal for

Users wanting a finished plug on both ends

Specifications

Item TypeConnector Cable
Connector TypeSMA Female to Stripping Head
Cable TypeRG1.13
Cable Length15
Connector Length (mm)11
Shipping Weight0.005 kg
Shipping Dimensions10 × 7 × 1 cm

What's in the box

  • 1 x 15 cm SMA female to stripping head connector cable, 11 mm RG1.13

Frequently Asked Questions

What is the stripping head end for?
It is an unfinished tail with the jacket removed and the shield separated and tinned, ready to solder to a board, terminal or antenna feed.
Will this fit my RP-SMA device?
No. The jack is standard SMA female, and standard SMA and RP-SMA connectors are not compatible.
What is the impedance and frequency range?
The cable and connector are rated at 50 Ohms and intended for use from DC to 18 GHz.
How long is the cable and connector?
The cable is 15 cm long and the SMA connector body measures 11 mm.
What is included in the package?
One 15 cm SMA female to stripping head connector cable with an 11 mm RG1.13 connector.
How should I care for the cable?
Avoid sharp bends and repeated twisting at the solder joint, and keep the connector clean and dry.

Overview

This 15 cm pigtail pairs a standard SMA female jack with a prepared stripping head, so one end plugs into an existing SMA port while the other is ready to solder. The stripping head has the outer jacket removed, the shield separated and tinned, which saves preparation time on small RF projects. RG1.13 is a thin, flexible coaxial cable, and the 11 mm connector body keeps the SMA end short where clearance is limited.

Key Features

  • SMA female to stripping head: one finished connector and one solder-ready tail.
  • RG1.13 coax: slim, flexible cable suited to short internal runs.
  • 15 cm length: enough reach for compact enclosures without excess slack.
  • 11 mm connector length: a short SMA body for crowded layouts.
  • Lightweight: about 5 g shipping weight, so it adds little to a build.

Specifications Explained

The SMA female end has a central receptacle inside a threaded barrel, so it mates with a standard SMA male plug. The 50 Ohm impedance matches common RF systems, and the design is intended for DC to 18 GHz service. The 15 cm length is measured on the cable, while the 11 mm figure describes the connector body. The stripping head is deliberately unfinished: the shield is separated and tinned, and the centre conductor is exposed for soldering. Plan the joint before you cut or trim anything, because the prepared tail is the working end.

Compatibility and Requirements

The SMA female jack accepts standard SMA male connectors. Standard SMA and RP-SMA are not interchangeable, so check the gender and polarity of the device or antenna you plan to mate with it. You will need soldering tools and a suitable termination point for the stripped end. The cable is not a plug-and-play adapter on the tail side.

Typical Uses

Common applications include WiFi antennas, LTE, GSM and CDMA antennas, 433 MHz antennas, base stations, handheld radios, telephone antennas, machine-to-machine communications, PC LAN links and radio astronomy setups. It is also handy for repairing a damaged antenna lead inside a small device.

What's in the Box

One 15 cm SMA female to stripping head connector cable with an 11 mm RG1.13 connector.

Connector Length and Cable Length

Quick specs

Item Type
Connector Cable
Connector Type
SMA Female to Stripping Head
Cable Type
RG1.13
Cable Length
15
Connector Length (mm)
11
Shipping Weight
0.005 kg
See all specifications