
1 / 3 · Click to enlarge
AI Summary
A compact 2-pin flat dial switch with 2.54mm pin pitch and through-hole mounting for PCB installation. Its low-profile body and simple dial make it a neat selector for tight boards and prototype layouts.
Key Highlights
- 2-pin flat dial switch with 2.54mm pin spacing
- Through-hole mounting for direct PCB soldering
- Compact 9.9 x 6.7 x 5.4mm body fits tight layouts
- 0.15A operating current for light-signal switching
- Rated from -40 to 85°C for varied environments
- Approximately 2000 mechanical and electrical cycles
Ideal For
- Makers building circuits on 2.54mm prototyping board
- Electronics hobbyists adding a compact selector to a project
- Technicians replacing a small dial switch on a PCB
- Designers working with tight board space and low profiles
- Students learning through-hole soldering and switch wiring
Buying Tip
Confirm your board uses 2.54mm pin pitch and keep the switched load below 0.15A, since this is a signal-level selector rather than a power switch.
Elecvora expert review
Our verdict
A tidy, low-profile selector for boards that already use a 2.54mm grid. It handles light signal switching well, provided you respect its current rating and cycle count.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Standard 2.54mm pitch simplifies board layout
- Compact flat body suits space-limited designs
- Through-hole pins give a secure soldered joint
- Wide -40 to 85°C operating range
Cons
- 0.15A rating limits it to signal-level circuits
- Around 2000 cycles suits occasional, not frequent, adjustment
- Requires soldering and a compatible drilled board
Best for
Occasional mode and option selection on compact PCBs
Not ideal for
Switching mains power or high-current loads
Specifications
| Manufacturer | Generic |
|---|---|
| Model No. / Name | 2 Pin Flat Dial Switch 2.54mm |
| Operating Current (A) | 0.15 |
| No. of Pins | 2 |
| Pin Spacing (mm) | 2.54 |
| Mounting Type | Through Hole |
| Operating Temperature (°C) | -40 to 85 |
| Mech. Electrical Lifecycle | ≈ 2000 |
| Length (mm) | 9.9 |
| Width (mm) | 6.7 |
| Height (mm) | 5.4 |
| Weight (g) | <1 |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
What's in the box
- 1 x 2 Pin Flat Dial Switch 2.54mm
Frequently Asked Questions
What is the pin pitch of this dial switch?
How is the switch mounted?
What current can it handle?
Does it need its own power supply?
What is included with the purchase?
How should I care for the switch?
Overview
The 2-Pin Flat Dial Switch 2.54mm is a small rotary selector designed for mounting directly onto a printed circuit board. Its two pins are spaced on a 2.54mm pitch, the familiar grid used by headers and prototyping board, which makes placement straightforward on both custom PCBs and hand-built circuits. The flat body measures 9.9mm long, 6.7mm wide and 5.4mm high, so it sits low and takes up little board area.
This is a through-hole part: the pins pass through the board and are soldered on the underside for a secure mechanical and electrical joint. The dial is turned to move between selectable settings, giving users a simple physical control for configuration or mode choice.
Key Features
- Standard 2.54mm pitch: aligns with common header and prototyping grids.
- Flat, compact body: useful where vertical clearance and board space are limited.
- Two-pin connection: a simple, dependable interface for light-signal circuits.
- Through-hole mounting: a solid soldered joint that resists movement.
- Wide temperature range: rated for operation from -40 to 85°C.
- Light weight: under 1g, so it adds negligible mass to a build.
Specifications Explained
Operating current of 0.15A tells you this is a signal-level switch. It is intended for low-current selection tasks, not for switching motors, heaters or main power rails. Keep it in control and logic paths.
2.54mm pin spacing is the key fit dimension. Check that your board or prototype layout uses this pitch before soldering; if it does, the switch seats without adapter work.
Mechanical and electrical life of approximately 2000 cycles means the switch is suited to settings that change occasionally. If a control will be turned many times a day, plan for replacement or choose a higher-cycle part.
The -40 to 85°C range covers most indoor and sheltered outdoor electronics, from cold storage to warm enclosures. The 9.9 x 6.7 x 5.4mm dimensions let you confirm clearance before assembly.
Compatibility and Requirements
The switch requires a board or prototype area drilled for 2.54mm-pitch through-hole pins, plus soldering equipment to fix it in place. It is a passive selector component, so it needs no separate power supply of its own. Ensure the circuit it switches stays within the 0.15A operating current rating.
Typical Uses
- Mode or option selection on small control boards
- Configuration settings on prototype and hobby circuits
- Signal routing in compact electronic assemblies
- Bench projects built on 2.54mm prototyping board
- Replacement selectors in space-constrained devices
What's in the Box
One 2-Pin Flat Dial Switch 2.54mm.
Quick specs
- Manufacturer
- Generic
- Model No. / Name
- 2 Pin Flat Dial Switch 2.54mm
- Operating Current (A)
- 0.15
- No. of Pins
- 2
- Pin Spacing (mm)
- 2.54
- Mounting Type
- Through Hole













