Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A three-piece copper and aluminium heat sink set with self-adhesive thermal layers for Raspberry Pi 2 and 3 boards. It provides quiet passive cooling that stays low enough to fit inside most cases.

Key Highlights

  • Three-piece set with two copper sinks and one aluminium sink
  • Self-adhesive thermal layer for tool-free mounting
  • Low-profile shapes that fit inside most standard cases
  • Passive cooling with no fan noise or extra power draw
  • Thermal resistance rated at 27 degrees C per watt
  • Lightweight set weighing about 8 g in total

Ideal For

  • Raspberry Pi 2 and 3 owners running long sessions
  • Makers building fanless or silent enclosures
  • Hobbyists working in warm rooms or closed cases
  • Beginners wanting a tool-free cooling upgrade
  • Users who prefer low-profile parts inside standard cases

Buying Tip

Check the free space above your Pi's chips and case lid before fitting, because the tallest sink in this set is 12 mm.

Elecvora expert review

Our verdict

A tidy, low-cost cooling set that does one job well: adding quiet passive heat spreading to a Raspberry Pi 2 or 3 without tools or fans. It will not match active cooling, but for typical light loads and cramped cases it is a sensible, low-risk addition.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Tool-free installation thanks to pre-applied thermal layers
  • Mixed copper and aluminium pieces in three useful sizes
  • No fan noise and no extra power draw
  • Very light at about 8 g for the set

Cons

  • Passive cooling has limited capacity under sustained heavy load
  • Suitable only for the stated Raspberry Pi 2 and 3 models
  • Adhesive is not described as reusable once applied

Best for

Quiet, low-profile cooling for Raspberry Pi 2 and 3 boards in standard cases

Not ideal for

High-load overclocking builds that need active fan cooling

Specifications

Item TypeHeatsink
Dimensions (L x W x H) mm13 x 12 x 5 9 x 9 x 12 12 x 12 x 1
MaterialCopper and Aluminium
Shipping Weight0.01 kg
Shipping Dimensions6 × 5 × 1 cm

What's in the box

  • 2 x copper heat sink
  • 1 x aluminium heat sink

Frequently Asked Questions

Which Raspberry Pi models does this set fit?
The set is described as designed for all versions of the Raspberry Pi 2 and Raspberry Pi 3. Other boards are not listed, so confirm your model first.
Do I need thermal paste or tools?
No. Each sink has a self-adhesive thermal layer already applied, so you only need to peel the backing and press the sink into place.
Will it fit inside my case?
The sinks are low profile, but the tallest piece is 12 mm, so check the clearance above your chips and under the case lid before fitting.
Does it need power or a fan?
No power connection is required. The set is fully passive, with no fan and no moving parts.
What is included in the set?
You receive two copper heat sinks and one aluminium heat sink, giving three pieces in total.
How should I look after the sinks?
Keep the fins free of dust and avoid pulling the sinks off once fitted, since the adhesive layer is intended for a single application.

Overview

This 3-in-1 heat sink set is a straightforward cooling accessory for Raspberry Pi 2 and 3 boards. It contains three separate sinks: two made from copper and one from aluminium. Each piece carries a self-adhesive thermal layer on its base, so installation is a matter of peeling and placing rather than mixing paste or driving screws.

The set is intended for passive cooling. Heat spreads from the chip into the sink and then into the surrounding air, with no fan to power, wire or listen to. That makes it a practical choice for builds where silence matters or where there is no room for active cooling.

Key Features

  • Two copper sinks and one aluminium sink in a single kit
  • Pre-applied self-adhesive thermal layer on each sink
  • Low-profile dimensions that suit most Raspberry Pi cases
  • Passive operation with no moving parts
  • Printed RPi logo on the set
  • Total set weight of approximately 8 g

Specifications Explained

The three sinks measure 13 x 12 x 5 mm, 9 x 9 x 12 mm and 12 x 12 x 1 mm. The differing heights and footprints let you match each sink to the chip it covers, while the 1 mm flat piece is thin enough to sit under tight clearances. Copper conducts heat quickly, which is why the two copper pieces are included alongside the aluminium sink.

The quoted thermal resistance of 27 degrees C per watt describes how much the sink resists heat flow. A lower figure means better transfer, and this rating gives you a realistic idea of what a small passive sink can do. The set weighs about 8 g, so it adds almost nothing to the board's load and will not stress a case or mounting point.

Compatibility and Requirements

The set is described as suitable for all versions of the Raspberry Pi 2 and Raspberry Pi 3. No other boards are specified, so check your model before fitting. No tools, thermal paste or additional hardware are required, because the thermal layer is already applied to each sink.

Typical Uses

Use the set when a Pi runs for long periods, sits in a warm room, or is mounted inside a closed enclosure with limited airflow. It also suits media centres, home servers and learning projects where fan noise would be unwelcome. Because the sinks are low profile, they are a sensible first cooling step before considering a larger case or an active solution.

What's in the Box

  • 2 x copper heat sink
  • 1 x aluminium heat sink

Quick specs

Item Type
Heatsink
Dimensions (L x W x H) mm
13 x 12 x 5 9 x 9 x 12 12 x 12 x 1
Material
Copper and Aluminium
Shipping Weight
0.01 kg
Shipping Dimensions
6 × 5 × 1 cm
See all specifications