
1 / 4 · Click to enlarge
AI Summary
A compact 4mm SPDT slide switch rated 50V DC at 0.5A, ideal for low-power PCB switching. Through-hole contacts and low 30mΩ resistance make it easy to solder and reliable in DIY electronics.
Key Highlights
- SPDT 1P2T contact configuration for two-way switching
- Rated 50V DC at 0.5A for low-power circuits
- Low 30mΩ contact resistance for minimal signal loss
- 100MΩ insulation resistance and 500V AC dielectric strength
- Compact 8.6mm × 3.7mm body fits dense PCB layouts
- Through-hole mounting for secure soldered connections
Ideal For
- DIY electronics hobbyists building custom circuits
- Makers prototyping on breadboards or PCBs
- Repair technicians replacing faulty slide switches
- Students learning about through-hole components
- Small-scale robotics and control panel builders
Buying Tip
Check that your circuit's voltage and current do not exceed 50V DC and 0.5A, and confirm the PCB footprint matches the through-hole pin spacing before ordering.
Elecvora expert review
Our verdict
A dependable, low-cost slide switch for low-power through-hole applications. It offers good isolation and low contact resistance in a compact size, though its 0.5A limit restricts it to light-duty use.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Compact size fits tight PCB layouts
- Low contact resistance of 30mΩ
- High insulation resistance and dielectric strength
- Lightweight and easy to handle
- Through-hole mounting for secure connections
Cons
- Limited to 0.5A current, not for high-power circuits
- Requires soldering for installation
- No datasheet or brand support included
Best for
Low-power DIY electronics and repair projects
Not ideal for
High-current or mains voltage applications
Specifications
| Manufacturer | Generic |
|---|---|
| Voltage Rating (V) | 50 |
| Rated Voltage (VDC) | 50 |
| Rated Current (A) | 0.5 |
| Contact Configuration | SPDT |
| Contact Type | Through-hole |
| Contact Resistance (ohm) | 30mΩ |
| Insulation Resistance (MOhm) | 100 |
| Dielectric Strength | 500V AC / 1 minute |
| Length (mm) | 8.6 |
| Width (mm) | 3.7 |
| Weight (g) | 1 (approx) (each) |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
What's in the box
- 1 x 4mm SPDT 1P2T Slide Switch
Frequently Asked Questions
What does SPDT mean on this switch?
Can this switch be used with AC voltage?
What is the maximum current this switch can handle?
Is this switch suitable for PCB mounting?
How many switches are included?
What are the dimensions of the switch?
Overview
The Generic 4mm SPDT 1P2T Slide Switch is a small, through-hole component designed to route a single input to one of two outputs. It is commonly used in DIY electronics, small power projects, and repair tasks where a manual selector is needed. With a 50V DC voltage rating and 0.5A current capacity, it handles low-power switching safely and reliably.
Key Features
- SPDT contact configuration: switches one pole between two throws for simple changeover control.
- Low contact resistance: at 30mΩ, it minimises voltage drop in signal and low-current paths.
- High insulation resistance: 100MΩ helps prevent leakage between circuits.
- Dielectric strength: 500V AC for 1 minute provides isolation confidence in low-voltage designs.
- Compact footprint: 8.6mm length and 3.7mm width suit tight PCB spaces.
- Lightweight: approximately 1g per switch, easy to handle during assembly.
Specifications Explained
Voltage and current ratings: The 50V DC rating and 0.5A maximum current mean this switch is intended for low-power circuits such as battery-operated devices, signal routing, and small control panels. Do not exceed these limits.
Contact resistance: A low 30mΩ value indicates that the switch will not significantly impede current flow, which is important for maintaining signal integrity in low-voltage applications.
Insulation resistance and dielectric strength: The 100MΩ insulation resistance and 500V AC dielectric strength (tested for 1 minute) indicate good isolation between contacts and the body, supporting safe operation in typical electronics environments.
Dimensions: At 8.6mm long and 3.7mm wide, the switch is compact enough for dense PCB layouts while remaining easy to solder by hand.
Compatibility and Requirements
This switch requires a through-hole PCB footprint and soldering for installation. It is suitable for circuits operating at or below 50V DC and 0.5A. No additional accessories are needed beyond standard soldering tools and a compatible PCB layout.
Typical Uses
- DIY electronics projects and breadboard prototypes
- Small power electronics and battery-powered devices
- Signal selection and mode switching in low-voltage circuits
- Repair or replacement of existing slide switches
- Hobbyist robotics and control panels
What's in the Box
1 x 4mm SPDT 1P2T Slide Switch.
Quick specs
- Manufacturer
- Generic
- Voltage Rating (V)
- 50
- Rated Voltage (VDC)
- 50
- Rated Current (A)
- 0.5
- Contact Configuration
- SPDT
- Contact Type
- Through-hole













