
1 / 3 · Click to enlarge
AI Summary
A 5cm RP-SMA female to IPEX1 adapter cable with a 13mm threaded connector and flexible RG1.13 coax. It lets you relocate an antenna socket from a small RF board to a panel or enclosure in tight builds.
Key Highlights
- 5cm RG1.13 coax pigtail for very short internal runs
- RP-SMA female to IPEX1 connector pairing
- 13mm threaded RP-SMA barrel for a secure mount
- Flexible RG1.13 cable eases routing in tight spaces
- Lightweight at about 5g shipping weight
- Suits antennas, RF boards and compact wireless projects
Ideal For
- FPV and RC builders working in tight airframes
- Makers adding an external antenna to a compact RF board
- Hobbyists repairing or shortening an antenna pigtail
- Wireless project builders using RP-SMA antennas
- Technicians fitting antenna sockets to small enclosures
Buying Tip
Check both ends before buying: your device needs an IPEX1 board connector and your antenna needs an RP-SMA male plug to mate with this female socket.
Elecvora expert review
Our verdict
A simple, well-sized pigtail for moving an RP-SMA antenna connection off a small board. It does one job cleanly, provided you match the connector types correctly.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Short 5cm length suits compact builds
- Flexible RG1.13 coax routes easily
- 13mm threaded barrel mounts securely
- Low cost and very light
Cons
- Only 5cm long, so reach is limited
- IPEX1 connectors are small and need careful handling
- RP-SMA will not mate with standard SMA gear
Best for
Compact RF and antenna builds needing a short RP-SMA to IPEX1 link
Not ideal for
Long cable runs or devices with standard SMA connectors
Specifications
| Item Type | Connector Cable |
|---|---|
| Connector Type | RP-SMA Female to IPEX1 |
| Cable Type | RG1.13 |
| Cable Length | 5 |
| Connector Length (mm) | 13 |
| Shipping Weight | 0.005 kg |
| Shipping Dimensions | 11 × 8 × 0.5 cm |
What's in the box
- 1 x 5CM RP-SMA Female to IPEX1 Connector Cable Thread 13mm RG1.13
Frequently Asked Questions
What does RP-SMA female mean on this cable?
Will this fit my board?
Can I use it with a standard SMA antenna?
How long is the cable?
What is included in the package?
How should I care for the cable?
Overview
This 5CM RP-SMA Female to IPEX1 Connector Cable is a short adapter pigtail that bridges two common antenna interfaces: a threaded RP-SMA female socket on one end and a compact IPEX1 board connector on the other. With only 5cm of flexible RG1.13 coax between them, it is built for situations where the antenna port needs to sit on a panel or enclosure while the radio board stays tucked inside.
The RP-SMA female end has a 13mm threaded barrel, giving you a proper screw-on mount for an RP-SMA antenna or extension. Reverse-polarity SMA is widely used on wireless gear, and matching the correct gender keeps your antenna setup consistent.
Key Features
- Short 5cm run: keeps the cable out of the way and minimises excess length inside small cases.
- RP-SMA female to IPEX1: connects a threaded antenna socket to a miniature board connector.
- 13mm threaded barrel: provides a secure, screw-on RP-SMA interface.
- RG1.13 coax: flexible cable that bends easily around components.
- Lightweight: shipping weight is just 0.005 kg, so it adds almost nothing to a build.
Specifications Explained
Connector types are the first thing to check. The RP-SMA female side has external threads and a centre pin, and it mates with an RP-SMA male plug. The IPEX1 side is the tiny snap-on connector found on many compact RF boards. Confirm your board uses IPEX1 before ordering.
Cable length of 5cm is deliberate. Short pigtails reduce signal loss and are easier to manage in handheld devices, small enclosures and dense builds. If you need to reach further, plan for an additional cable rather than stretching this one.
RG1.13 is a thin, flexible coax. It is a practical choice when the cable has to curve tightly, though its small diameter means it is best kept to short runs like this one.
13mm connector length describes the threaded RP-SMA barrel, which is useful when checking whether the socket will clear a panel or case wall.
Compatibility and Requirements
Use this cable only with equipment that has an RP-SMA female socket and an IPEX1 board connector. Note that RP-SMA and standard SMA look similar but do not mate correctly, so verify the polarity of your antenna and device first. No other accessories are required to fit the cable itself.
Typical Uses
- Moving an antenna socket to the outside of a small wireless enclosure.
- Connecting an RP-SMA antenna to a compact RF board with an IPEX1 port.
- Short internal links in FPV, telemetry and hobby radio builds.
- Replacing a damaged or overly long pigtail in a tight layout.
What's in the Box
1 x 5CM RP-SMA Female to IPEX1 Connector Cable, 13mm thread, RG1.13.

Quick specs
- Item Type
- Connector Cable
- Connector Type
- RP-SMA Female to IPEX1
- Cable Type
- RG1.13
- Cable Length
- 5
- Connector Length (mm)
- 13
- Shipping Weight
- 0.005 kg













