
1 / 3 · Click to enlarge
AI Summary
A 6x6x8mm momentary through-hole tactile switch rated 12V at 50mA with IP65 protection and brass contacts. Its defined 1.56N tactile feedback makes it a dependable input button for PCBs and breadboard prototypes.
Key Highlights
- 6x6x8mm through-hole momentary push button for PCB mounting
- IP65 protection against dust and water splashes
- Brass contacts with low 50mΩ contact resistance
- 1.56N operating force for clear tactile feedback
- 12V DC, 50mA rating with 100MΩ insulation resistance
- Approximately 50,000 mechanical operating cycles
Ideal For
- Electronics hobbyists building breadboard prototypes
- PCB designers needing a compact momentary input switch
- Repair technicians replacing worn tactile buttons
- Product developers testing control panel layouts
- Students learning through-hole soldering and switching circuits
Buying Tip
Confirm your circuit stays within 12V DC and 50mA, and check that the 8mm height and 6x6mm footprint fit your enclosure or PCB layout before ordering.
Elecvora expert review
Our verdict
A well-specified miniature tactile switch that balances a compact footprint with IP65 protection and clear tactile feedback. It is a sensible choice for low-power through-hole designs where dust and splash resistance matter.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- IP65 rating adds dust and splash protection
- Low 50mΩ contact resistance for stable signals
- Clear 1.56N tactile feedback
- Compact 6x6x8mm through-hole package
- Approximately 50,000-cycle mechanical life
Cons
- Rated for only 12V and 50mA, so unsuitable for higher-power loads
- Requires soldering for permanent PCB installation
- Package contents are not specified
Best for
Low-power PCB and breadboard projects needing a protected momentary input button
Not ideal for
Switching mains voltages or currents above 50mA
Specifications
| Manufacturer | Generic |
|---|---|
| Operating Voltage (VDC) | 12 |
| Max. Operating Current (A) | 50mA |
| On/Off Function | Push to ON |
| Switch Type | Momentary |
| Contact Type | Through-hole |
| Contact Material | Brass |
| Contact Resistance (ohm) | 50mΩ |
| Insulation Resistance (MOhm) | 100 |
| Operating Temperature (°C) | -20 to 70°C |
| Operation Force | 1.56 +/- 0.5 N |
| Operation Stroke | 0.25+0.2/-0.1mm |
| Body Material | Plastic |
| Mech. Electrical Lifecycle | ≈ 50000 |
| Protection Standard | IP65 |
| Length (mm) | 6 |
| Width (mm) | 6 |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
Frequently Asked Questions
Is this switch momentary or latching?
Can I use this switch on a breadboard?
What voltage and current can it handle?
How many switches are included?
Is the switch waterproof?
How should I care for the switch?
Overview
The 6x6x8mm Tactile Push Button Switch is a compact momentary switch designed for through-hole mounting on printed circuit boards and solderless breadboards. Pressing the button closes the circuit and releasing it opens the circuit again, making it a straightforward way to add a manual input to electronic projects. The switch combines a 6mm by 6mm body with an 8mm profile and uses brass contacts for stable electrical conduction.
With an IP65 protection standard, the switch is shielded against dust ingress and water splashes, which helps in environments where contamination is possible. The 1.56N operating force and 0.25mm stroke produce a crisp tactile response, so users can feel when the contact has been made.
Key Features
- Momentary push-to-ON action: the circuit is completed only while the button is held down.
- Through-hole contact type: pins are designed for soldering into PCB holes or temporary breadboard use.
- Brass contact material: supports reliable conductivity with a low contact resistance of 50mΩ.
- IP65 protection: resists dust and water splashes for use in more demanding settings.
- Compact 6x6x8mm body: fits into tight layouts without taking up unnecessary board space.
- Long service life: rated for approximately 50,000 mechanical electrical cycles.
Specifications Explained
The 12V DC operating voltage and 50mA maximum operating current define the switch for low-power signal and control circuits rather than mains or high-current loads. Contact resistance of 50mΩ means the switch adds very little resistance when closed, while the 100MΩ insulation resistance indicates good isolation when open.
The operating temperature range of -20 to 70°C covers typical indoor and protected outdoor electronics. The operation force of 1.56 ± 0.5N gives a light but noticeable press, and the operation stroke of 0.25 +0.2/-0.1mm is short and precise. The plastic body keeps the component lightweight, with a shipping weight of just 0.001 kg.
Compatibility and Requirements
This switch is intended for through-hole PCB mounting and can also be used in solderless breadboards for temporary prototypes. It requires a circuit operating within 12V DC and 50mA. No additional drivers or modules are needed; the switch is a passive electromechanical component. Soldering is required for permanent PCB installation.
Typical Uses
Common applications include user input buttons on consumer electronics, test and instrumentation panels, medical device controls, audio/visual equipment, computer peripherals and general prototyping. The IP65 rating also makes it suitable for household appliances and other products where occasional splashes may occur.
What's in the Box
Package contents are not specified for this listing. Please check the product packaging or contact the seller for details on quantity and included items.

Quick specs
- Manufacturer
- Generic
- Operating Voltage (VDC)
- 12
- Max. Operating Current (A)
- 50mA
- On/Off Function
- Push to ON
- Switch Type
- Momentary
- Contact Type
- Through-hole















