Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 7-position blue flat dial switch with 2.54mm pitch for manual circuit configuration on PCBs. It lets you set addresses and function options by hand without any programming.

Key Highlights

  • Seven dial positions for manual circuit configuration
  • Standard 2.54mm pitch fits common PCB layouts
  • Rated 25mA at 24VDC for low-current signal switching
  • Contact resistance of 100 milliohms or less
  • Compact blue body around 20 x 10 x 10mm
  • Mechanical life rated for 2000 operations

Ideal For

  • Electronics prototypers setting board options by hand
  • Embedded systems developers configuring device addresses
  • Industrial control board designers needing manual mode selection
  • Communication equipment technicians setting hardware options
  • Makers building compact through-hole PCB assemblies

Buying Tip

Confirm your board uses a 2.54mm seven-pin footprint and keep the switched signal within 25mA at 24VDC, since this is a low-current configuration part.

Elecvora expert review

Our verdict

A practical little part for anyone who needs seven manual settings on a board without adding firmware controls. Its low-current rating and 2000-operation life suit occasional configuration changes rather than frequent switching.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Seven positions in one compact part
  • Standard 2.54mm pitch simplifies layout
  • Low contact resistance for signal paths
  • Clear blue body is easy to spot on a board

Cons

  • Limited to low-current signals at 25mA and 24VDC
  • Rated for 2000 operations, so not for frequent changes
  • No detailed model or datasheet information supplied

Best for

Manual address and function setting on low-current PCB designs

Not ideal for

Switching mains power, motors or high-current loads

Specifications

Shipping Weight0.005 kg
Shipping Dimensions3 × 3 × 3 cm

What's in the box

  • 1 x 7Pin Blue Flat Dial switch 2.54mm

Frequently Asked Questions

What is this switch used for?
It sets circuit options by hand, such as device addresses, function selection or operating parameters, without any software change.
What voltage and current can it handle?
The contact rating is 25mA at 24VDC, with a maximum switching voltage of 24VDC. It is intended for low-current signal circuits.
Does the 2.54mm pitch fit standard boards?
Yes, 2.54mm is a common through-hole spacing, but always check your own board footprint and pin count before ordering.
How many settings does it provide?
It has seven dial positions, so up to seven independent settings can be made on the one component.
What is included with the switch?
The package contains one 7-pin blue flat dial switch with 2.54mm pitch.
How should I care for it?
Keep it within -25°C to +70°C, avoid excessive force when turning the dials, and limit changes to what the 2000-operation rating allows.

Overview

The Generic 7-pin blue flat dial switch is a through-hole component for setting circuit options directly on a board. Instead of editing firmware, you turn the dial positions to choose an address, select a function or change an operating parameter. The 2.54mm pitch lines up with standard prototyping boards and many existing PCB layouts, so the part fits where a similar footprint is already used.

It is a low-current signal switch, rated at 25mA and 24VDC, which makes it suitable for configuration and addressing rather than power switching. The blue body measures about 20 x 10 x 10mm and weighs roughly 2g.

Key Features

  • Seven dial positions for manual hardware configuration
  • 2.54mm pin pitch for common through-hole PCB layouts
  • Low-current contact rating of 25mA at 24VDC
  • Contact resistance of 100 milliohms or less
  • Insulation resistance of at least 100 megohms
  • Dielectric strength of 250 to 500VAC for one minute
  • Compact blue housing around 20 x 10 x 10mm

Specifications Explained

The 7-pin layout gives you seven independent dial positions, so several settings can be made on one component. The 2.54mm pitch is the familiar spacing used on many prototyping boards and through-hole assemblies, which helps when planning a layout.

The 25mA at 24VDC contact rating tells you this is a signal-level part. It is intended for low-current logic and configuration lines, not for motors, relays or main power paths. Contact resistance of 100 milliohms or less keeps the on-state path low, while insulation resistance of at least 100 megohms describes how well the open positions isolate. Dielectric strength of 250 to 500VAC for one minute is a short-duration withstand figure, not a continuous working voltage.

The operating range of -25°C to +70°C covers most indoor and sheltered electronics. Mechanical life is rated at 2000 operations, so the switch suits settings that are changed occasionally rather than constantly.

Compatibility and Requirements

The switch is designed for PCB mounting with a 2.54mm pitch and seven pins. It works in low-current signal circuits within the 24VDC and 25mA contact rating. No other compatibility details are specified, so check your board footprint and signal levels against these figures before fitting.

Typical Uses

Common applications include setting device addresses, choosing between operating modes, and configuring options on communication equipment, industrial control boards and embedded systems. It also suits prototyping, where a manual setting is quicker than a code change.

What's in the Box

One 7-pin blue flat dial switch with 2.54mm pitch.

Quick specs

Shipping Weight
0.005 kg
Shipping Dimensions
3 × 3 × 3 cm
See all specifications