Skip to main content
Free Delivery  ·  COD Available  ·  15-Day Returns
Elecvora
CH376S USB Module U Disk Read Write Module — image 1
Hover to zoom

1 / 2 · Click to enlarge

CH376S USB Module U Disk Read Write Module

33+ bought in past month
AI Summary
Boards Compatible with Arduino for everyday users

The CH376S USB Module U Disk Read Write Module is a value-for-money boards compatible with arduino designed for everyday users. It features Item Type: Development Board and Chip Type: CH376S.

₹719
Free Shipping💵 COD Available

Available Offers

Free Delivery on this order. No minimum order value.

15-Day Easy Returns — hassle-free return & full refund.

Secure Payment — 100% safe checkout with UPI, Cards & Net Banking.

Total: ₹719
Buying tip: A smart budget buy — solid performance without breaking the bank.
Estimated delivery: 24 Aug7 Sept
Free Shipping
Pan India delivery
15-Day Returns
Hassle-free policy
Secure Payment
Razorpay protected
Quality Assured
Vetted products only

Available Offers

💳

5% Cashback

Pay with UPI & get 5% cashback (up to ₹50) via Razorpay

🏦

No-Cost EMI

Available on select bank cards at checkout. 0% interest for 3 months.

📦

Free Shipping

Free delivery on all orders. No minimum order value.

💵

Cash on Delivery

COD available on orders up to ₹5,000 across India.

Quick Specs

Item Type: Development Board
Chip Type: CH376S
Operating Voltage (VDC): 5
Interface: SPI
Supported Formats: FAT12, FAT16, FAT32
Speed: 2MBPS

Ideal For

Everyday convenience
Share:
SKU: robu-815821Category: Boards Compatible with Arduino

About This Product

The CH376S USB Module U Disk Read Write Module is a value-for-money boards compatible with arduino designed for everyday users. It delivers reliable performance at an accessible price.

Key Specifications

  • Item Type: Development Board
  • Chip Type: CH376S
  • Operating Voltage (VDC): 5 — works with standard household power
  • Interface: SPI — compatible with modern devices
  • Supported Formats: FAT12, FAT16, FAT32 — compatible with modern devices
  • Speed: 2MBPS
  • Length (mm): 43
  • Width (mm): 22

Why Buy from Elecvora?

Elecvora sources this product directly, cutting out multiple middlemen. Every order includes free shipping, a 15-day return policy, and secure payment via Razorpay.

CH376S is used as a file manage control chip, used to MCU system read/write a file in USB Flash Drive or SD card. It supports USB-Device Mode and USB-HOST Mode. It also sets firmware of special communication protocol to deal with Mass-Storage devices, communication interface firmware of SD card, FAT16, FAT32, and FAT12 file system manage firmware in the inner. CH376S supports three communication interfaces: an 8-bit parallel, SPI interface or asynchronism serial interface.

Features:

  1. Internal curing CH376S chip FAT file system, file operations simple and fast
  2. Support including USB thumb drives, USB hard drives, USB flash drives and USB storage devices, USB card reader
  3. Support standard size SD card, HC-SD card, and compatible high capacity MMC, TF card
  4. Supports a variety of communication interfaces: 8-bit parallel, SPI interface, and asynchronous serial ports
  5. Compatibility: device is compatible with CH372, host compatible with CH375

Package Includes:

1 x CH376S USB Module U Disk Read Write Module

Setup Guide

1
Identify the pins
Locate VCC (power), GND (ground), and data pins (SDA/SCL for I2C, MOSI/MISO for SPI, or TX/RX for UART). Refer to the pinout diagram on the product page.
2
Wire to your microcontroller
Connect VCC to 3.3V or 5V (check the module spec), GND to GND, and data pins to the appropriate GPIO pins on your Arduino or Raspberry Pi.
3
Install libraries
In Arduino IDE, go to Sketch → Include Library → Manage Libraries and search for the sensor library. Install the recommended version.
4
Upload example sketch
Open File → Examples → [library name] → Basic Example. Upload to your board and open Serial Monitor to view output.
5
Calibrate if needed
Some sensors (temperature, humidity, distance) may need a short warm-up period or calibration. Run the calibration sketch if provided.