
1 / 3 · Click to enlarge
AI Summary
A pre-soldered ESP32-C3 development board with Wi-Fi, BLE 5.0 and two 7A relays that runs directly from 110-240V AC mains. USB-C programming, GPIO switch inputs and OTA updates make it a practical base for custom IoT switching projects.
Key Highlights
- ESP32-C3-WROOM-02 with RISC-V core up to 160 MHz
- Wi-Fi 802.11 b/g/n and Bluetooth 5.0 LE onboard
- Two G5LE-1 relays rated 7A at 220V AC
- Direct 110-240V AC input via HLK-PM01 converter
- USB Type-C for flashing and serial communication
- Two active-low GPIO inputs for manual switch control
Ideal For
- Developers prototyping custom Wi-Fi and BLE switches
- Smart home hobbyists building relay-based automation
- Makers replacing bare ESP32 modules with a mains-ready board
- Automation enthusiasts needing OTA-updatable control nodes
- Technicians building light industrial switching prototypes
Buying Tip
Confirm that each appliance you plan to switch stays within the 7A at 220V AC relay rating before wiring it to the board.
Elecvora expert review
Our verdict
A tidy integration of ESP32-C3 wireless, a mains supply and two relays that saves considerable design work. It is a development board first, so expect to write or adapt firmware rather than unbox a finished consumer product.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Mains-ready with onboard HLK-PM01 converter
- Two 7A relays cover most household switching tasks
- USB-C plus OTA make development and updates convenient
- Pre-soldered and compact at 65 x 44 x 20 mm
Cons
- Requires your own firmware and ESP32-C3 toolchain
- Mains wiring demands proper electrical competence
- Relay rating limits heavier appliances
Best for
Developers and makers building custom mains-switched IoT devices
Not ideal for
Buyers wanting a plug-and-play consumer smart plug
Specifications
| Shipping Weight | 0.060 kg |
|---|---|
| Shipping Dimensions | 9 × 6 × 3 cm |
What's in the box
- 1 x eSync ESP32-C3 Smart Switch DIY Dev Board
Frequently Asked Questions
What voltage does the board accept?
How do I program the board?
How much load can each relay handle?
Can I use a normal wall switch with it?
What is included in the package?
Does it support firmware updates after installation?
Overview
The eSync ESP32-C3 Smart Switch DIY Dev Board combines a wireless microcontroller, a mains power stage and two relays on one compact PCB. It is aimed at people who want to build their own connected switches without designing a power supply or relay driver from scratch. The board arrives pre-soldered, so you can move straight to firmware and wiring.
At its centre is the ESP32-C3-WROOM-02 module, built on a 32-bit RISC-V core running at up to 160 MHz with Wi-Fi 802.11 b/g/n and Bluetooth 5.0 LE. A Hi-Link HLK-PM01 converter takes 110-240V AC and produces 5V DC, while an AMS1117 regulator supplies 3.3V to the logic. Two G5LE-1 relays switch loads up to 7A at 220V AC.
Key Features
- Integrated mains supply: no separate DC adapter is needed for the board itself.
- Dual relay outputs: control two independent AC circuits such as lights, fans or sockets.
- USB Type-C interface: flash firmware and use serial communication over UART on GPIO20 and GPIO21.
- Local switch inputs: two active-low GPIO inputs let a conventional wall switch trigger the board.
- OTA updates: revise firmware over the network after the board is installed.
- Status LED: a GPIO1 indicator gives simple visual feedback.
Specifications Explained
The 7A relay rating at 220V AC defines the load ceiling per channel; check the current draw of your appliance before connecting it. Relay logic is active high, meaning a high signal on the control pin energises the coil, while the two switch inputs are active low. The 5V DC output is rated 0.6A and 3W, which is enough for the board and light external logic, not for powering heavy loads.
The ESP32-C3 provides 2.4 GHz Wi-Fi and BLE 5.0, so the board can join a local network or act as a Bluetooth endpoint. The USB Type-C port handles both flashing and serial debugging, and the AMS1117 regulator keeps the 3.3V rail stable for the module.
Compatibility and Requirements
The board accepts 110-240V AC at 50/60 Hz with an input current of 0.2A. You will need a USB Type-C cable and a computer to program it, plus a suitable ESP32-C3 development toolchain. Mains wiring should only be carried out by someone competent to work with AC voltages.
Typical Uses
- Custom smart switches for lights, fans and sockets
- Home automation prototypes with local and remote control
- Light industrial control and equipment switching
- Teaching and development projects around ESP32-C3 firmware
What's in the Box
1 x eSync ESP32-C3 Smart Switch DIY Dev Board. The board measures 65 x 44 x 20 mm and weighs 57 g.













