
1 / 6 · Click to enlarge
At a glance
This tools, industrial & scientific is a good fit for DIY builders and repair work. Main specs: parameter Specification; display size 4” TFT LCD (480×320); max low input frequency 800MHz, 6GHz in Ultra mode.
Key Highlights
- Parameter: Specification
- Display size: 4” TFT LCD (480×320)
- Max low input frequency: 800MHz, 6GHz in Ultra mode
Ideal For
- Repairs around the home
- Electronics bench work
- Workshop jobs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Parameter | Specification |
|---|---|
| Display size | 4” TFT LCD (480×320) |
| Max low input frequency | 800MHz, 6GHz in Ultra mode |
| Resolution filters in 1,3,10 steps | from 200Hz to 850kHz |
| Max output frequency | Sinus up to 800MHz |
| output level | -104dBm to -16dBm |
| Ultra mode | Level calibrated up to 5.3GHz |
| Internal LNA gain | 20dB up to 4GHz |
| Displayed points per scan | max 450 |
| 0-350MHz scan time | 165ms |
| Shortest zero span time | 17ms |
| DANL at 100MHz | -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) |
| DANL degrading in ultra mode | 10dB above 2.5GHz, 25dB above 5.3GHz |
| Phase noise at 10kHz bias | -92dBc/Hz |
| Phase noise at 100kHz bias | -110dBc/Hz |
| Input 1dB compression level | +0.5dBm (LNA Off) / -26.5dBm (LNA On) |
| IIP3 without LNA | +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) |
| IIP3 with LNA | -8dBm (at least 2MHz apart) |
| Frequency stability | <1ppm ( -10℃ ~ +55℃) |
| SD card slot | micro SD card |
| Audio out | 3.5mm headphone plug |
| FW update mode activation | Push jog button before switch on |
| Maximum current consumption | 330mA |
| Maximum charging current | 1300mA |
| Battery | Li-polymer 3.7V 3000mAh |
| RF connectors | SMA female |
| Communication Interface | USB-CDC(Type-C),UART-TTL(2.54mm Connector) |
| Appearance Size | 117x72x23mm (Excluding protruding parts) |
Overview
The Handheld 4" Display Tiny Spectrum Analyzer TinySA ULTRA 100kHz to 5.3GHz with 32GB Card Version V0.4.5.1 is listed in our tools, industrial & scientific range and suits DIY builders and repair work. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Parameter: Specification
- Display size: 4” TFT LCD (480×320) (measured diagonally; compare with the space you have before ordering)
- Max low input frequency: 800MHz, 6GHz in Ultra mode (make sure the rest of your system works at this frequency)
- Resolution filters in 1,3,10 steps: from 200Hz to 850kHz (space for firmware, files or media)
- Max output frequency: Sinus up to 800MHz (make sure the rest of your system works at this frequency)
- output level: -104dBm to -16dBm
- Ultra mode: Level calibrated up to 5.3GHz (make sure the rest of your system works at this frequency)
- Internal LNA gain: 20dB up to 4GHz (make sure the rest of your system works at this frequency)
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
Official version, supports the latest firmware, cooperates with Zeenko
Features:
- Screen size 4 inch
- Spectrum Analyzer for 0.1-800MHz or, with Ultra mode enabled, 0.1MHz-6GHz
- Signal Generator with sine wave output between 0.1-800MHz or dual tone output up to 4.4GHz when not used as Spectrum Analyzer.
- Switchable resolution bandpass filters for both ranges between 200Hz and 850kHz
- Built-in 20dB optional LNA
- Color display showing 450 scan points covering up to the full frequency range.
- Input Step attenuator from 0dB to 31dB (not in combination with LNA).
- A built-in calibration signal generator that is used for automatic self test and (low) input calibration.
- Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer or Signal Generator
- Rechargeable battery allowing a minimum of at least 2 hours portable use
- Max input level +10dBm. Do not destroy your tinySA
- Due to the low cost and very small form factor there are certain relevant tinySA limitations and tinySA Ultra limitations
Specification:
Package includes:
1 x Host
1 x USB Type-C data cable
2 x 30cm ALSR100 SMA cables
1 x SMA-SMA barrel connector
1 x Antenna with SMA connector
1 x Lanyard and touch plectrum
1 x 32GB MicroSD card(plugged in the host)






Quick specs
- Parameter
- Specification
- Display size
- 4” TFT LCD (480×320)
- Max low input frequency
- 800MHz, 6GHz in Ultra mode
- Resolution filters in 1,3,10 steps
- from 200Hz to 850kHz
- Max output frequency
- Sinus up to 800MHz
- output level
- -104dBm to -16dBm










