Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The JHEMCU RX24T is a lightweight ExpressLRS 2.4GHz receiver with a 500Hz refresh rate and 5V input. Its 0.6g weight and simple LED-guided binding make it an easy fit for compact FPV and RC builds.

Key Highlights

  • ExpressLRS 2.4GHz receiver with 500Hz refresh rate
  • Ultra-light 0.6g weight without the antenna
  • ESP8285 MCU paired with SX1280IMLTRT RF chip
  • Runs on a 5V supply from the flight controller
  • Compact body that is easy to install
  • LED status for binding, signal, and WiFi upgrade

Ideal For

  • FPV pilots building lightweight 2.4GHz ExpressLRS quads
  • RC helicopter builders needing a compact receiver
  • Makers and hobbyists upgrading to ExpressLRS control
  • Pilots flying weight-sensitive micro and sub-250g builds

Buying Tip

Confirm your radio and transmitter module run 2.4GHz ExpressLRS before buying, since this receiver will not bind to other protocols.

Elecvora expert review

Our verdict

The RX24T is a tidy, lightweight ExpressLRS receiver that covers the basics well: a 2.4GHz link, 500Hz refresh rate, and a clear LED status system. It is a sensible pick for compact builds where every gram counts.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Very light at 0.6g without antenna
  • 500Hz refresh rate for responsive control
  • Clear LED feedback for binding and signal status
  • Includes T antenna and wiring

Cons

  • Requires a 2.4GHz ExpressLRS transmitter module and compatible radio
  • Only 5V operating voltage is specified
  • Binding process takes a few careful USB cycles

Best for

Lightweight FPV and RC helicopter builds using 2.4GHz ExpressLRS

Not ideal for

Pilots using non-ExpressLRS radio systems or higher-voltage receiver setups

Specifications

Item TypeReceiver
Frequency (GHz)2.4
Model No. / NameRX24T
Weight (g)0.6g(without antenna)
Refresh Rate (Hz)500
Operating Voltage (V)5V
Shipping Weight0.02 kg
Shipping Dimensions6 × 6 × 1 cm

What's in the box

  • 1 x RX24T RC Receiver
  • 1 x T antenna
  • 4 x Wire

Frequently Asked Questions

What radio system does the RX24T work with?
It is an ExpressLRS receiver for the 2.4GHz band, so it needs a 2.4GHz ExpressLRS transmitter module and a compatible radio.
How do I bind the receiver?
Power the flight controller over USB and unplug as soon as the receiver LED turns off, repeating this twice. On the third USB connection the LED double flashes into binding mode, then run ELRS.LUA on the radio to bind.
What voltage does the receiver need?
The RX24T operates on 5V. Check that your supply matches before connecting it.
What do the LED flashes mean?
Double flash means binding mode, slow flash means no transmit signal is received, steady on means a transmit signal is received, and fast flash means WiFi upgrade mode.
What is included with the receiver?
The package contains one RX24T RC receiver, one T antenna, and four wires.
How much does the receiver weigh?
It weighs 0.6g without the antenna, so account for the antenna when planning your build weight.

Overview

The JHEMCU RX24T is an ExpressLRS receiver designed for the 2.4GHz band. Inside the small housing sit an ESP8285 microcontroller and an SX1280IMLTRT RF chip, a combination that supports the responsive control link ExpressLRS is known for. At just 0.6g without the antenna, it keeps added weight minimal on compact airframes.

The receiver runs on 5V and offers a 500Hz refresh rate. Binding follows the standard ExpressLRS routine, and an onboard LED communicates what the receiver is doing at each stage, from binding mode to a confirmed link.

Key Features

  • 2.4GHz ExpressLRS link: a widely used control protocol for FPV and RC builds.
  • 500Hz refresh rate: fast, frequent control updates for responsive flying.
  • Lightweight design: 0.6g without antenna helps keep builds light.
  • ESP8285 MCU and SX1280IMLTRT RF: the core processing and radio hardware.
  • LED status feedback: double flash for binding mode, slow flash when no signal is received, steady on when a transmit signal is received, and fast flash for WiFi upgrade mode.
  • Simple installation: compact dimensions and included wiring make mounting straightforward.

Specifications Explained

2.4GHz frequency: the receiver works on the 2.4GHz band, so it pairs with 2.4GHz ExpressLRS transmitter modules. 500Hz refresh rate: a higher refresh rate means the control link updates more often, which suits pilots who want tight, immediate stick response. 5V operating voltage: the receiver expects a 5V supply, typically from the flight controller, so check your power source before connecting. 0.6g weight: quoted without the antenna, this is the figure to consider when planning weight-sensitive builds. The small shipping dimensions of 6 x 6 x 1 cm reflect its compact footprint.

Compatibility and Requirements

The RX24T requires a 2.4GHz ExpressLRS transmitter module and a compatible radio to bind. Binding uses the ELRS.LUA script, which is placed on the radio's SD card in the SD Card/Scripts/tools directory and then run. The receiver needs a 5V supply and is intended to be connected to a flight controller. A T antenna and wiring are included for the install.

Typical Uses

This receiver suits FPV drone builds where low weight and a fast control link are priorities. It also works well in RC helicopters, as noted in the product features, and in other small radio-controlled models that use a 2.4GHz ExpressLRS setup. Its compact size makes it easy to tuck into tight frames.

What's in the Box

  • 1 x RX24T RC Receiver
  • 1 x T antenna
  • 4 x Wire

Quick specs

Item Type
Receiver
Frequency (GHz)
2.4
Model No. / Name
RX24T
Weight (g)
0.6g(without antenna)
Refresh Rate (Hz)
500
Operating Voltage (V)
5V
See all specifications