
1 / 4 · Click to enlarge
AI Summary
A compact 12V DC linear actuator with a 200mm stroke that pushes or pulls up to 1500N at about 7mm/s no-load speed. Its built-in limit switch and IP55 aluminium housing make it a straightforward fit for beds, sofas, TV lifts and light automation projects.
Key Highlights
- 200mm stroke with 1500N maximum push and pull force
- Runs on 12VDC and draws 2A or less
- No-load speed of 7mm/s, about 5.5mm/s under full load
- Built-in limit switch stops travel at both ends
- IP55 protection with moisture-resistant aluminium frame
- Quiet operation at around 45dB with self-locking holding force
Ideal For
- Furniture makers building adjustable beds and recliner sofas
- Makers and hobbyists automating TV lifts and camera sliders
- Technicians servicing solar tracking and light agricultural frames
- Workshop and booth builders adding powered linear movement
- DIY automation enthusiasts working with 12V DC systems
Buying Tip
Confirm your mechanism has clearance for the 317mm body plus the full 200mm extension, and pair the actuator with a 12VDC supply and a reversing controller rated for at least 2A.
Elecvora expert review
Our verdict
A solid, no-frills 12V actuator for furniture and light automation where 1500N and a 200mm stroke are enough. The built-in limit switch, IP55 housing and self-locking design make it easy to integrate, as long as you respect the load and duty limits.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Built-in limit switch protects travel at both ends
- Self-locking 1500N holding force
- IP55 aluminium housing with moisture-proof surface
- Quiet operation around 45dB
- Low 2A maximum current draw
Cons
- Slow travel at about 7mm/s no load
- No power supply or controller included
- High-frequency use and high temperatures shorten life
Best for
Adjustable furniture, TV lifts, camera sliders and light automation projects
Not ideal for
Continuous heavy-duty industrial cycling or wet, immersed environments
Specifications
| Operating Voltage (VDC) | 12 |
|---|---|
| Stroke Length (mm) | 200 |
| Force (N) | 1500 |
| Speed (mm/s) | 7 |
| Operating Temperature (°C) | -20 to +63 |
| Mounting Hole Diameter (mm) | 1/4” (6.4mm) |
| Protection level | IP55 |
| Max. Static Load | 337.2 lbs. ( 1500 Newtons ) |
| Max. Current Draw (A) | ≤2A |
| Motor diameter (mm) | 36 mm |
| Speed at No Load (mm/Sec) | 0.28in/sec (7 mm /sec) |
| Speed at Full Load (mm/Sec) | 0.22in/sec (5.5 mm/sec) |
| Noise (dB) | 45 dB |
| Length (mm) | 317 |
| Width (mm) | 77 |
| Weight (g) | 1034 |
| Shipping Weight | 1.05 kg |
| Shipping Dimensions | 33 × 9 × 4.5 cm |
What's in the box
- 1 x Linear Actuator, Stroke Length 200mm, 7mm/s, 1500N, 12V
Frequently Asked Questions
What voltage does this linear actuator need?
How fast does it move and how long is a full stroke?
Does it stop automatically at the end of travel?
What is included with the actuator?
Can it be used outdoors?
How do I mount it?
Overview
The Generic 12V linear actuator is an electric push rod that turns the rotary motion of a permanent magnet DC motor into straight-line push and pull movement. With a 200mm stroke, it extends and retracts a load over that distance while providing up to 1500N of force. The aluminium frame and extension tube keep the unit compact at 317mm long and 77mm wide, and the motor body measures 36mm in diameter.
Because the actuator is self-locking at 1500N, it holds position when power is removed, which is useful for adjustable furniture and positioning mechanisms. A built-in limit switch cuts travel at each end of the stroke, helping protect the motor and gear train during normal use.
Key Features
- 12VDC operation with a maximum current draw of 2A, suitable for common DC supplies.
- 200mm stroke for medium-travel lifting, tilting and sliding tasks.
- 1500N force (about 337.2 lbs static load) for pushing and pulling moderate loads.
- 7mm/s no-load speed, dropping to about 5.5mm/s under full load.
- Built-in limit switch to stop the rod at the end of each stroke.
- IP55 protection and a moisture-proof surface for sheltered indoor and outdoor use.
- Quiet running at roughly 45dB, useful in living and working spaces.
- Mounting holes of 1/4 inch (6.4mm) diameter at each end for pin or bolt fixing.
Specifications Explained
Stroke length is the distance the rod travels from fully retracted to fully extended: 200mm here. Check that this matches the movement your mechanism needs, and allow room for the 317mm body length plus the extended rod.
Force and load are rated at 1500N, and the maximum static load is the same figure. Static load refers to holding force rather than a guarantee for continuous dynamic pushing, so keep working loads comfortably below the maximum.
Speed is 7mm/s with no load and about 5.5mm/s at full load, so a full 200mm stroke takes roughly 29 to 36 seconds depending on load. Plan cycle times accordingly.
Voltage and current are 12VDC and 2A or less. Never connect the actuator to AC power, and stay within the rated voltage.
Environment: the operating range is -20 to +63 degrees Celsius, and IP55 protection covers dust and water jets but not immersion. High-frequency operation and high temperatures can shorten service life.
Compatibility and Requirements
You need a 12VDC power source able to supply up to 2A, plus a reversing switch or relay-based controller to extend and retract the rod. Mounting pins or bolts sized for the 6.4mm (1/4 inch) mounting holes are required and are not included. The actuator does not include a power supply or controller.
Typical Uses
- Adjustable beds, massage beds and medical-style chairs
- Recliner sofas, electric lifting levers and TV lift tables
- Camera frames, sliders and positioning rigs
- Solar tracking frames and light agricultural mechanisms
- Workshop, booth and sunroof automation projects
What's in the Box
1 x Linear Actuator, 200mm stroke, 7mm/s, 1500N, 12V.

Quick specs
- Operating Voltage (VDC)
- 12
- Stroke Length (mm)
- 200
- Force (N)
- 1500
- Speed (mm/s)
- 7
- Operating Temperature (°C)
- -20 to +63
- Mounting Hole Diameter (mm)
- 1/4” (6.4mm)













