
1 / 3 · Click to enlarge
AI Summary
The LP-1 is a clip-on logic probe that indicates high, low, high-impedance and pulse states on DTL, TTL and CMOS circuits. Its pulse memory mode captures brief transitions so you can confirm activity at a test point.
Key Highlights
- Indicates high, low, high-impedance and pulse states via LEDs
- Works with DTL, TTL and CMOS logic families
- Accepts a 3-18 VDC supply from the circuit under test
- 20 MHz operating frequency for fast digital signals
- Pulse memory mode stores detected transitions for review
- Compact, lightweight design for bench and field use
Ideal For
- Electronics repair technicians tracing faults on digital boards
- Students learning TTL and CMOS logic behaviour
- Hobbyists checking signal activity in DIY circuits
- Bench engineers who need a fast logic state check
Buying Tip
Check that your circuit's supply falls within 3-18 VDC before clipping the probe on, and remember the probe takes its power from the board under test rather than an internal battery.
Elecvora expert review
Our verdict
A practical, no-fuss logic probe that gives fast visual answers on DTL, TTL and CMOS boards. The pulse memory mode is the standout feature for catching transitions a level test would miss.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Clear four-state LED indication
- Pulse memory latches brief transitions
- Wide 3-18 VDC supply range
- Logic family selector for TTL/DTL and CMOS
- Lightweight and easy to carry
Cons
- No internal battery, so it relies on the circuit under test for power
- Requires access to the board's supply rails for the clips
- Rated to 20 MHz, so not intended for very high-speed signals
Best for
Bench troubleshooting of DTL, TTL and CMOS digital circuits
Not ideal for
Very high-speed digital designs or circuits outside the 3-18 VDC supply range
Specifications
| Item Type | Digital Tester |
|---|---|
| Model No. / Name | Logic Tester |
| Supply Voltage | 3-18 VDC |
| Compatibility | Supports DTL, TTL, and CMOS logic circuits |
| Operating Frequency (MHz) | 20MHz |
| Shipping Weight | 0.082 kg |
| Shipping Dimensions | 26 × 9 × 3 cm |
What's in the box
- 1 x LP-1 DTL TTL CMOS Pulse Memory Logic Tester Probe
Frequently Asked Questions
How is the LP-1 powered?
Which logic families does it support?
What do the LEDs mean?
How does the pulse memory work?
What is included with the probe?
What frequency can it handle?
Overview
The LP-1 is a handheld logic probe for tracing digital signals in DTL, TTL and CMOS circuits. Instead of interpreting voltage readings on a meter, you clip the probe to the supply rails of the board you are testing and touch the tip to a node. Colour-coded LEDs then report the logic condition at that point, giving a quick answer during fault finding or circuit checks.
Key Features
- Four-state indication: all LEDs off means high impedance, red means a high state, green means a low state and orange signals a pulse.
- Pulse memory: switch to MEM to latch a detected pulse or level transition, then compare it with the original state to judge activity at the node.
- Logic family selection: an upper selector lets you match the probe to TTL/DTL or CMOS thresholds.
- Wide supply range: the probe runs from 3-18 VDC taken from the circuit under test.
- Fast response: a 20 MHz operating frequency covers many common digital signal rates.
Specifications Explained
The 3-18 VDC supply range means the probe draws its power from the same rails as the circuit being checked, so no separate battery is required. The upper switch sets the input thresholds for TTL/DTL or CMOS logic, which matters because the two families define high and low levels differently. The 20 MHz figure describes the operating frequency the probe is rated for, so it is suited to typical digital clock and data lines rather than very high-speed designs. The pulse memory function is the practical extra here: brief transitions that are easy to miss on a level test can be captured and confirmed.
Compatibility and Requirements
The LP-1 supports DTL, TTL and CMOS logic circuits within a 3-18 VDC supply. It requires access to the positive and negative supply points of the circuit under test for the red and black clips. No additional power source is listed.
Typical Uses
Useful for bench troubleshooting of digital boards, checking clock and data lines, confirming signal activity after a repair, classroom demonstrations of logic states and general hobby electronics work where a quick state check is faster than a meter reading.
What's in the Box
One LP-1 DTL TTL CMOS pulse memory logic tester probe.
Quick specs
- Item Type
- Digital Tester
- Model No. / Name
- Logic Tester
- Supply Voltage
- 3-18 VDC
- Compatibility
- Supports DTL, TTL, and CMOS logic circuits
- Operating Frequency (MHz)
- 20MHz
- Shipping Weight
- 0.082 kg













