
1 / 3 · Click to enlarge
AI Summary
A 24-piece pack of M3 x 5mm male-female brass hex standoffs for mounting and elevating PCBs. The hex body tightens with a wrench and the brass construction resists corrosion.
Key Highlights
- 24 matching M3 x 5mm brass standoffs in one pack
- Male-to-female threading for stacking and board elevation
- Hexagonal body can be tightened with a standard wrench
- Brass resists rust, oxidation and heat exposure
- 5 mm height creates clearance and airflow space around boards
- Suits PCB mounting in frames, cases and driver boards
Ideal For
- DIY electronics builders mounting PCBs in enclosures
- Drone and RC frame builders spacing controller boards
- Makers assembling motor driver and sensor boards
- Computer chassis modders raising boards off metal
- Students and hobbyists working on prototype hardware
Buying Tip
Confirm your board and chassis use M3 threads and that 5 mm of clearance is enough before ordering, since the height is fixed.
Elecvora expert review
Our verdict
A straightforward, well-made hardware pack that does one job reliably: lifting and holding M3-threaded boards at a fixed 5 mm height. The brass body and hex profile make installation easier than finger-tight plastic spacers.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Brass resists corrosion and handles warm enclosures
- Hex body allows wrench tightening
- Male-female threading supports stacking
- 24 pieces give consistent spares
Cons
- Screws are not included
- Fixed 5 mm height limits adjustment
- Only suits M3-threaded mounting points
Best for
Makers and builders mounting M3-threaded PCBs in frames, cases and prototypes
Not ideal for
Builds needing adjustable height or non-M3 thread sizes
Specifications
| Item Type | Brass Hex Standoff Spacer |
|---|---|
| Quantity | 24 Pcs |
| Spacer Height (mm) | 5 |
| Thread Size | M3 |
| Gender | Male to female |
| Shipping Weight | 0.03 kg |
| Shipping Dimensions | 4 × 4 × 1 cm |
What's in the box
- 24 x M3 x 5mm male-female brass hex threaded standoff spacers
Frequently Asked Questions
What does male-to-female mean on these standoffs?
Are screws included with the standoffs?
What is the 5 mm measurement?
Can I tighten these by hand?
Will brass standoffs conduct electricity?
How should I care for them?
Overview
These M3 x 5mm male-female brass hex standoffs are small but essential hardware for anyone mounting circuit boards. Each piece has a male thread on one end and a female thread on the other, letting you raise a board off a surface or stack boards at a fixed distance. The pack contains 24 identical standoffs, enough for several small projects or one larger build with spare parts left over.
The 5 mm spacer height sets a consistent gap between the board and whatever sits below it. That gap matters when components need room to breathe, when solder joints must not touch a metal chassis, or when you simply want a clean, serviceable assembly.
Key Features
- Male-to-female design: one threaded stud and one threaded bore per standoff for flexible mounting.
- M3 thread size: matches common small PCB mounting holes and M3 screws.
- 5 mm spacer height: a defined, repeatable clearance for airflow and insulation.
- Hexagonal profile: flat sides allow tightening with a wrench instead of fingers alone.
- Brass construction: resists oxidation and corrosion and keeps good electrical conductivity.
- 24-piece quantity: consistent parts for multi-board builds.
Specifications Explained
M3 thread refers to the metric thread size, which is the practical detail to check against your board and screws. Male-to-female means each standoff can screw into a threaded hole or nut on one side and accept a screw on the other, so it works both as a riser and as a stacking element.
The 5 mm height is the body length between the two threaded ends, giving you a fixed stand-off distance. Because the body is hexagonal, you can hold or turn it with a wrench, which helps when you need a firm, vibration-resistant joint. Brass was chosen for its resistance to rust and oxidation, its mechanical strength, and its electrical conductivity.
Compatibility and Requirements
These standoffs are intended for M3-threaded mounting points. You will need matching M3 screws or threaded holes on the board or chassis side, and the 5 mm height should suit the clearance your layout requires. No other hardware is supplied in the pack beyond the standoffs themselves, so plan for screws, nuts or threaded inserts as your build demands.
Typical Uses
- Raising PCBs inside computer chassis and enclosures
- Mounting motor driver boards and controller boards
- Spacing boards on quadcopter and RC frames
- General DIY electronics and prototype assemblies
- Creating airflow clearance around heat-producing components
What's in the Box
24 x M3 x 5mm male-female brass hex threaded standoff spacers. Screws and other fasteners are not included.
Quick specs
- Item Type
- Brass Hex Standoff Spacer
- Quantity
- 24 Pcs
- Spacer Height (mm)
- 5
- Thread Size
- M3
- Gender
- Male to female
- Shipping Weight
- 0.03 kg
Frequently Bought Together

6-in-1 RC Multi-Size Wrench Tool 3,4,5,5.5,7,8mm Turnbuckle and Nut Repair Tool
$7.99
One ALLEN KEY and Ten GRUB Screw M3*4 Set for Timing Pulley of 3D Printers
$5.99
Aluminum Quick-Release Bullet Cap Wrench M3/M5/M6 for RC Motor Parts
$8.99
Hexagonal Mini Cross Wrench Sleeve Nut Tool for M2/M2.5/M3/M4 Hex Nuts
$5.99










