Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A slim black ABS enclosure for the Raspberry Pi 4 Model B with a fan slot above the processor and a ventilation grill for airflow. It snaps and screws together easily while keeping every port, the micro-SD card and the status LEDs accessible.

Key Highlights

  • Black ABS shell sized for the Raspberry Pi 4 Model B
  • Dedicated cooling fan slot positioned over the processor
  • Ventilation grill on the side opposite the USB ports
  • All ports, status LEDs and micro-SD card remain accessible
  • Locking notches plus four screws for quick assembly
  • Anti-slip rubber feet and a lightweight 52 g build

Ideal For

  • Raspberry Pi 4 owners who want a low-cost protective shell
  • Makers building always-on home lab or media nodes
  • Students and classroom Pi 4 kits
  • Desktop users who prefer a tidy, finished look
  • Hobbyists planning to add a 4010S fan for airflow

Buying Tip

Check that your fan is a DC 5V 0.2A 4010S unit before ordering, since the fan and the Pi 4 board are both sold separately from this case.

Elecvora expert review

Our verdict

A practical, inexpensive shell that covers the basics well: accurate port openings, a fan slot over the processor and a ventilation grill for airflow. It is not a heavy-duty enclosure, but for everyday Pi 4 protection it does the job neatly.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Precise cut-outs keep every Pi 4 port usable
  • Fan slot and ventilation grill support airflow
  • Tool-light assembly with notches and four screws
  • Micro-SD card reachable from the bottom panel
  • Lightweight at 52 g with anti-slip feet

Cons

  • Pi 4 board and cooling fan are not included
  • ABS plastic offers basic rather than rugged protection
  • Only two heat sinks are supplied

Best for

Budget-conscious Pi 4 owners who want a tidy case with room for a fan

Not ideal for

Users needing a rugged, sealed or weather-resistant enclosure

Specifications

CompatibilityPi 4
ColorBlack
Additional Specs.Cooling Fan Slot
Length (mm)90
Width (mm)63
Weight (g)52
SupportedAll Variant of Pi 4 Models B
Shipping Weight0.07 kg
Shipping Dimensions13 × 9 × 3 cm

What's in the box

  • 1 x Black ABS case for Raspberry Pi 4 with cooling fan slot
  • 1 x Screw set
  • 2 x Heat sink

Frequently Asked Questions

Does this case fit every Raspberry Pi 4 Model B version?
Yes, it is listed as compatible with all variants of the Raspberry Pi 4 Model B. The Raspberry Pi board itself is not included.
Is a cooling fan included?
No. The case has a slot for a DC 5V 0.2A 4010S cooling fan, but the fan must be purchased separately.
Can I access the micro-SD card without opening the case?
Yes. There is a cut-out for the micro-SD card in the bottom panel, so card changes do not require removing the screws.
How is the case held together?
The two halves align with locking notches and are secured by four small screws from the supplied screw set.
Will the status LEDs be visible?
Yes, the design leaves the Pi status LEDs visible so you can check activity without opening the enclosure.
What are the dimensions and weight?
The case measures approximately 90 mm by 63 mm and weighs about 52 g.

Overview

This black ABS case is a simple, well-thought-out housing for the Raspberry Pi 4 Model B. Its rounded edges and accurately cut openings give the board a tidy finished look while leaving every connector usable. The shell measures roughly 90 mm by 63 mm and weighs only 52 g, so it protects the Pi without turning it into a bulky box.

Cooling has been considered in the design. A cooling fan slot sits directly above the processor area and accepts a DC 5V 0.2A 4010S fan, while a ventilation grill on the opposite side of the USB ports gives warm air a path out of the enclosure. Together these openings support continuous operation in typical desktop and project setups.

Key Features

  • Moulded from smooth black ABS plastic for everyday protection
  • Fan slot positioned over the processor chip
  • Ventilation grill opposite the USB ports
  • Precise cut-outs for all Pi 4 ports and the status LEDs
  • Micro-SD card opening in the bottom panel
  • Locking notches and four screws hold the case closed
  • Anti-slip rubber feet on the base

Specifications Explained

Size and weight

At about 90 mm long, 63 mm wide and 52 g, the case stays close to the footprint of the board itself. That makes it easy to fit into tight project enclosures, behind a monitor or on a small desk.

Cooling fan slot

The slot is intended for a DC 5V 0.2A 4010S cooling fan. If you plan to run the Pi under sustained load, this opening lets you add active airflow without modifying the shell.

Port access and LEDs

Each connector opening is aligned with the Pi 4 layout, so USB, Ethernet, HDMI, audio and power ports stay usable. The status LEDs remain visible, which helps when you are checking boot and activity without opening the case.

Assembly hardware

Locking notches guide the two halves together, and four small screws secure them. The bottom panel includes a cut-out for the micro-SD card, so you can swap cards without dismantling the case.

Compatibility and Requirements

The case supports all variants of the Raspberry Pi 4 Model B. The Raspberry Pi 4 board itself is not included. A DC 5V 0.2A 4010S cooling fan is optional and also not supplied, so add one separately if you want active cooling.

Typical Uses

This enclosure suits home lab nodes, media players, retro gaming builds, classroom kits and general desktop Pi setups where a neat, protected board is preferred. The fan slot makes it a reasonable pick for always-on services, and the visible LEDs are handy for quick status checks.

What's in the Box

  • 1 x Black ABS case for Raspberry Pi 4 with cooling fan slot
  • 1 x Screw set
  • 2 x Heat sink

Quick specs

Compatibility
Pi 4
Color
Black
Additional Specs.
Cooling Fan Slot
Length (mm)
90
Width (mm)
63
Weight (g)
52
See all specifications