
1 / 5 · Click to enlarge
AI Summary
A tiny 433.92MHz wireless receiver and remote set that drives a DC motor forward, reverse and stop from up to a distance. Its 0.5mA standby draw suits battery-powered builds and small enclosures.
Key Highlights
- Wireless up, down, stop, forward and reverse motor commands
- 433.92MHz operating frequency for remote control
- Rated voltage range of 3 to 12VDC
- Low 6mA working current and 0.5mA standby draw
- Compact 21 x 11mm module fits tight spaces
- Lightweight at around 50g total
Ideal For
- Makers building small DC motor automation projects
- RC and model hobbyists needing remote direction control
- DIY enthusiasts adding remote up and down movement
- Technicians prototyping compact motor mechanisms
- Hobbyists working with 3 to 12VDC battery-powered builds
Buying Tip
Confirm your motor supply stays within the 3 to 12VDC range and budget for your own wiring, since leads are not included.
Elecvora expert review
Our verdict
A neat, low-draw wireless switching module for small DC motor jobs where space is tight and you want remote direction control. It is simple and compact, but you must supply your own wiring and keep the load within sensible limits.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Very small 21 x 11mm receiver board
- Low 0.5mA standby draw suits battery builds
- Wide 3 to 12VDC input range
- Five control actions from one remote
Cons
- Wiring is not included
- No motor current rating is stated, so check your load
- Generic brand with limited documentation
Best for
Small DC motor projects needing remote forward, reverse and stop control
Not ideal for
High-power motors or builds needing documented current ratings
Specifications
| Rated Voltage (VDC) | 3 to 12 |
|---|---|
| Working Current (mA) | 6ma |
| Standby current | 0.5ma |
| Operating Frequency (Hz) | 433.92MHZ |
| Length (mm) | 21 |
| Width (mm) | 11 |
| Weight (g) | 50 |
| Shipping Weight | 0.05 kg |
| Shipping Dimensions | 3 × 2 × 1 cm |
What's in the box
- 1 x Up Down Stop Forward Reverse Wireless Mini Motor Remote Switch Controller DC 12V
Frequently Asked Questions
What does this controller actually do?
What voltage can I use?
Is wiring included?
How much power does it draw?
What frequency does the remote use?
How big is the receiver?
Overview
This mini wireless motor switch controller gives you directional control of a DC motor without a wired switch panel. A small receiver module accepts commands from the supplied remote, letting you run the motor forward, reverse it, or stop it on demand, along with up and down movement control. The radio link uses the 433.92MHz band, a widely used frequency for short-range remote control.
The module is built for tight installations. At roughly 21mm long and 11mm wide, it slips into small enclosures, model housings and custom fixtures where a full-size controller would not fit. The whole set weighs around 50g, so it adds little bulk to portable builds.
Key Features
- Five control actions: up, down, stop, forward and reverse from the remote.
- Wide voltage range: rated for 3 to 12VDC, so it can run from small battery packs or a 12V supply.
- Low power use: 6mA while working and 0.5mA on standby, helpful for battery-powered projects.
- Compact footprint: 21 x 11mm receiver module.
- 433.92MHz radio link: a common short-range control frequency.
Specifications Explained
Rated voltage (3 to 12VDC): the module accepts a range of supply voltages, giving you flexibility when matching it to your motor and power source. Always keep the supply within this range.
Working current (6mA): this is the module's own draw while it is actively receiving or switching. It is a low figure, so the controller itself will not drain a battery quickly.
Standby current (0.5mA): when idle, the module draws very little, which matters for builds that sit unused for long periods.
Operating frequency (433.92MHz): the remote and receiver communicate on this band. Keep the receiver antenna area clear of metal where possible for reliable reception.
Dimensions (21 x 11mm): a very small receiver board that suits compact housings and space-limited assemblies.
Compatibility and Requirements
The controller is designed for DC motor switching within the stated 3 to 12VDC range. Wiring is not supplied with the module, so you will need your own leads and connectors. The motor and power source you use should match the voltage range given above. Because the receiver handles switching rather than motor drive, check that your motor current is appropriate for the switching circuit you build.
Typical Uses
- Remote direction control for small DC motor projects
- Model and hobby builds needing forward, reverse and stop
- DIY window, blind or vent adjusters using a small motor
- Remote up and down movement in compact mechanisms
- Prototype automation where wired switches are inconvenient
What's in the Box
Package includes 1 x Up Down Stop Forward Reverse Wireless Mini Motor Remote Switch Controller DC 12V. Note that the wiring shown in product images is for illustration and is not included.
Quick specs
- Rated Voltage (VDC)
- 3 to 12
- Working Current (mA)
- 6ma
- Standby current
- 0.5ma
- Operating Frequency (Hz)
- 433.92MHZ
- Length (mm)
- 21
- Width (mm)
- 11













