
1 / 3 · Click to enlarge
AI Summary
A 20-pin JTAG ISP AVR cable with 2.54mm pitch and 310mm length, ideal for connecting debuggers and programmers to PCB headers. Its 28 AWG ribbon construction keeps the lead flexible and easy to route during testing.
Key Highlights
- Standard 2.54mm pitch for common JTAG headers
- 20-pin dual-row connector (2 x 10 pins)
- 310mm cable length for flexible board access
- 28 AWG wire for a slim, pliable lead
- Lightweight at just 17g
- Suitable for PCB testing and firmware programming
Ideal For
- Embedded systems engineers debugging PCBs
- Electronics technicians performing boundary-scan tests
- Makers and hobbyists programming AVR boards
- Field service engineers updating firmware on site
- Students learning JTAG-based development
Buying Tip
Confirm that your target board and programmer both use a 2.54mm pitch 20-pin JTAG header before ordering, as this cable is a passive lead with no adapters included.
Elecvora expert review
Our verdict
A simple, well-made passive cable that does exactly what it should: connect a 20-pin JTAG header to your debugging tool. The 310mm length and 28 AWG wire make it easy to handle on the bench.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Standard 2.54mm pitch fits common headers
- 20-pin dual-row layout for JTAG interfaces
- Lightweight and flexible for easy routing
- Sufficient 310mm length for most bench setups
Cons
- No adapters included for other pitch sizes
- Passive cable only; no active components
- Requires matching 20-pin headers on both ends
Best for
Engineers and technicians working with 2.54mm 20-pin JTAG headers
Not ideal for
Boards with non-standard pitch or pin count
Specifications
| Manufacturer | Generic |
|---|---|
| Pitch Spacing (mm) | 2.54 |
| Connector Type | JTAG |
| No. of Pins | 20 |
| Length (mm) | 310 |
| Width (mm) | 30 |
| Weight (g) | 17 |
| Cable Length | 30 |
| Wire Size (AWG) | 28 |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
What's in the box
- 1 x 2.54mm Pitch 20 Pin JTAG ISP AVR Cable
Frequently Asked Questions
What is this cable used for?
Will it fit my board?
Does it require external power?
What is included in the package?
How should I care for the cable?
Is it compatible with all embedded systems?
Overview
The Generic 2.54mm Pitch 20 Pin JTAG ISP AVR Cable is a dedicated ribbon lead for connecting JTAG-compatible embedded systems to debugging and programming hardware. It features a 20-pin connector arranged in two rows of 10 pins, matching the standard JTAG header footprint found on many development boards and manufactured PCBs. The cable is 310mm long and 30mm wide, giving you a practical reach for bench work and field diagnostics. At only 17g, it adds negligible weight to your toolkit.
Key Features
- 20-pin JTAG connector with 2.54mm pitch spacing
- Dual-row pin layout (2 x 10) for standard JTAG ports
- 310mm overall length for flexible positioning
- 28 AWG wire construction for a slim, flexible cable
- Lightweight design at 17g
- Designed for PCB verification, testing and firmware updates
Specifications Explained
Pitch spacing (2.54mm): This is the distance between pin centres. 2.54mm is a widely used standard for through-hole and header connectors, so this cable fits common JTAG headers without adapters. Number of pins (20): The 20-pin configuration is a common JTAG interface size, providing enough lines for debugging and boundary-scan signals. Length (310mm): The cable gives you roughly 31cm of reach, which is helpful when your programmer or debugger sits a short distance from the target board. Wire size (28 AWG): Thinner wire keeps the cable flexible and easy to route around components, while remaining suitable for low-current signal connections. Weight (17g): Light enough to hang from a header without pulling or strain.
Compatibility and Requirements
This cable is intended for JTAG-compatible embedded systems platforms that use a 2.54mm pitch 20-pin header. It supports plug-in debugging, firmware programming and boundary-scan testing. No additional adapters are included. You will need a host programmer or debugger with a matching 20-pin JTAG interface and a target board with a compatible header. The cable does not include any active electronics; it is a passive connection lead.
Typical Uses
- Connecting a JTAG debugger to a development board
- Programming firmware on AVR and other embedded platforms
- Boundary-scan testing of assembled PCBs
- Field updates and troubleshooting of embedded devices
- Bench testing during design verification
What's in the Box
1 x 2.54mm Pitch 20 Pin JTAG ISP AVR Cable.
Quick specs
- Manufacturer
- Generic
- Pitch Spacing (mm)
- 2.54
- Connector Type
- JTAG
- No. of Pins
- 20
- Length (mm)
- 310
- Width (mm)
- 30













