Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A two-channel 4-wire PWM controller that varies fan speed according to temperature from two NTC 10K probes, with an LED readout and buzzer alarm. It runs on DC 10-60V and shows both temperature and RPM.

Key Highlights

  • Two independent temperature-controlled fan channels on one board
  • DC 10-60V operating range for 12V, 24V and 48V systems
  • NTC 10K B=3950 probes with 9.9°C to 99.9°C measuring range
  • LED display alternates temperature and fan speed readings
  • Adjustable minimum speed and temperature control zone via buttons
  • Switchable buzzer alarm triggers below 375rpm

Ideal For

  • Electronics hobbyists building temperature-controlled enclosures
  • Makers cooling 3D printer or equipment cabinets
  • Technicians servicing 12V, 24V or 48V fan systems
  • DIY builders adding automatic ventilation to a project box
  • Anyone replacing a fixed-speed fan setup with temperature-linked control

Buying Tip

Confirm your fans are four-wire Intel-spec models rated for your supply voltage before ordering, since two- and three-wire fans will not work with this board.

Elecvora expert review

Our verdict

A practical two-channel board for anyone who wants fans to follow real temperature rather than run flat out. It is best suited to builders who already use four-wire fans and are comfortable setting thresholds by button.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Two independent temperature-controlled channels
  • Wide DC 10-60V operating range
  • Clear LED readout of temperature and RPM
  • Adjustable minimum speed and temperature zone
  • Switchable stall alarm

Cons

  • Cannot control two- or three-wire fans
  • Cannot fully switch a fan off
  • Fan connector pins limited to 3A

Best for

Temperature-linked cooling in 12-48V four-wire fan installations

Not ideal for

Two-wire or three-wire fans, or setups needing complete fan shutdown

Specifications

Item TypeSpeed Controller
Operating Voltage (V)DC10-60V
Working Current (mA)35mA (12V), 22mA (24V)
ProbesNTC 10K B=3950
Temperature Control (°C)Acceleration temperature 5-94℃, full speed temperature 10-99℃
Measuring Temperature (°C)9.9°C to 99.9°C
Shipping Weight0.035 kg
Shipping Dimensions10 × 9 × 1.5 cm

What's in the box

  • 1 x 2CH 4 Wire LED Digital PWM Motor Speed Controller Fan Temperature Controller Buzzer Alarm with 50CM Cable

Frequently Asked Questions

Which fans can this controller drive?
Only four-wire fans that follow Intel's four-wire fan specification, which includes most 12-48V four-wire fans. Two-wire and three-wire fans are not supported.
Can it switch the fan completely off?
No. The output range is 10% to 100%, so the fan keeps receiving a signal rather than stopping entirely.
What supply voltage do I need?
The board operates from DC 10-60V, but the fans must be rated for the supply you use. The supply has to meet the fan's voltage requirements.
What if my fan draws more than 3A?
The fan connector pins on the board are limited to 3A. For higher-current fans, connect the fan power leads directly to the main supply.
How are temperature and speed displayed?
The LED display alternates between the two channels' temperature readings and their fan speeds, shown in steps of 10rpm.
Is the buzzer alarm on by default?
No. The stop alarm is off by default and can be switched on; it sounds when a fan drops below 375rpm.

Overview

This compact controller gives you two independent fan channels, each driven by a four-wire PWM signal and linked to its own temperature probe. Instead of running fans at a fixed speed, it raises and lowers output as the measured temperature changes, so cooling responds to real conditions. Settings are entered with the onboard buttons and saved by the program, so they survive a power cycle.

Key Features

  • Dual-channel control: two fans can be managed separately, each with its own temperature reading and speed setting.
  • Wide operating voltage: the board works from DC 10V to 60V, covering common 12V, 24V and 48V installations.
  • LED digital display: alternates between probe temperature and fan speed so you can check both at a glance.
  • Buzzer alarm: a switchable stop alarm sounds if a fan drops below 375rpm; it is off by default.
  • 50cm cable: gives useful reach between the board, the fans and the probes.

Specifications Explained

Voltage: the controller accepts DC 10-60V, but the fans themselves must be rated for whatever supply you use. Match the fan voltage to the supply before connecting anything.

Current draw: the board consumes about 35mA at 12V and 22mA at 24V, so it adds very little load to your supply.

Temperature range: the probes measure from 9.9°C to 99.9°C. You can set an acceleration temperature between 5°C and 94°C and a full-speed temperature between 10°C and 99°C, which defines how gradually the fan ramps up.

Speed readout: rotation is shown in steps of 10rpm up to 9990rpm; above that the display holds at 999. Measurement assumes a common two-pole signal fan.

Output range: the PWM signal spans 10% to 100%. The actual minimum speed depends on how the connected fan responds.

Board size: 65 x 65 x 15mm with 56 x 56mm mounting hole spacing and 3.2mm hole diameter.

Compatibility and Requirements

This is a four-wire PWM fan controller. It works only with fans that follow Intel's four-wire fan specification, which covers most 12-48V four-wire fans. It cannot control two-wire or three-wire fans, and it cannot fully switch a fan off. The fan connector pins on the board are limited to 3A; for higher-current fans, wire the fan power leads directly to the main supply. The supply must meet the fan's own voltage requirements.

Typical Uses

  • Temperature-linked cooling inside equipment enclosures and cabinets
  • Ventilation control in DIY electronics and power projects
  • Quieting fan noise by lowering speed when temperatures are low
  • Adding a stall warning to an existing cooling setup

What's in the Box

One 2CH 4-wire LED digital PWM motor speed controller with fan temperature controller and buzzer alarm, supplied with a 50cm cable.

Quick specs

Item Type
Speed Controller
Operating Voltage (V)
DC10-60V
Working Current (mA)
35mA (12V), 22mA (24V)
Probes
NTC 10K B=3950
Temperature Control (°C)
Acceleration temperature 5-94℃, full speed temperature 10-99℃
Measuring Temperature (°C)
9.9°C to 99.9°C
See all specifications