
1 / 6 · Click to enlarge
AI Summary
A pack of two back-to-back AA battery holders with pre-attached wires and spring clips for quick cell loading. Each holder is slim, light at about 5 g, and gives you roughly 140 mm of wire for wiring into a project.
Key Highlights
- Pack of two back-to-back AA battery holders
- Spring clip design for easy cell loading and removal
- Pre-attached wires around 140 mm long
- Slim 25 mm width suits compact builds
- Lightweight at about 5 g per holder
- Simple two-cell holder for DIY and repair work
Ideal For
- Hobby electronics builders making compact battery packs
- Students working on low-voltage school or college projects
- Repairers replacing a damaged AA holder
- Makers building slim enclosures and custom gadgets
- Anyone needing a spare two-cell AA holder
Buying Tip
Check that the roughly 140 mm wire length and 25 mm holder width fit your enclosure before you commit to the layout.
Elecvora expert review
Our verdict
A simple, lightweight two-cell AA holder that is easy to load and quick to wire in. The back-to-back shape and pack of two make it a sensible spare part for small projects.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Spring clips make cell changes easy
- Wires already attached, saving assembly time
- Slim 25 mm width suits tight spaces
- Very light at about 5 g each
- Two holders in the pack
Cons
- No mounting hardware included
- Wire ends may need adapting to your circuit
- Cells are not included
Best for
Compact DIY and repair projects needing a two-cell AA holder
Not ideal for
Projects that need a sealed, ready-made battery pack
Specifications
| Item Type | Battery Holder |
|---|---|
| Compatibility | AA Battery |
| Width (mm) | 25 |
| Wire Length (mm) | 140 |
| Weight (g) | 5(each) |
| Shipping Weight | 0.02 kg |
| Shipping Dimensions | 12 × 10 × 2 cm |
What's in the box
- 2 x 2x AA Battery Back to Back Holder Case Box with wires
Frequently Asked Questions
What batteries does this holder take?
How long are the wires?
How many holders are included?
Does it come with batteries?
How wide is each holder?
How much does each holder weigh?
Overview
This is a pack of two AA battery holders designed to hold two AA cells in a back-to-back arrangement. Each holder comes with wires already attached, so you can route power to your circuit without adding separate contacts or a battery clip. The spring clip design keeps cells seated while still making them easy to insert and remove.
The back-to-back format keeps the holder narrow, which helps in small enclosures, DIY projects and repairs where a side-by-side block would take up too much room. At about 5 g per holder and 25 mm wide, the part adds very little bulk to a build.
Key Features
- Two-cell back-to-back layout: holds two AA batteries in a slim, flat arrangement.
- Spring clip design: cells press in and lift out without tools.
- Pre-attached wires: roughly 140 mm of wire per holder for reaching your connection point.
- Lightweight build: about 5 g per holder, so it barely affects the weight of a project.
- Pack of two: useful as a spare or for projects that need two holders.
Specifications Explained
Compatibility: the holder is made for AA batteries. Use cells that match the holder's contacts and your project's requirements.
Width: at 25 mm, the holder is narrow enough for compact layouts where space is limited.
Wire length: each holder has about 140 mm of wire, giving you a short run to a switch, terminal block or circuit board.
Weight: about 5 g per holder keeps the assembly light, which matters in small handheld or portable builds.
Compatibility and Requirements
This holder is intended for AA batteries only. It is a holder and wiring part, not a complete power supply, so you will need your own AA cells and a project or device to connect it to. Check that the wire ends suit your connection method before fitting the holder into a closed enclosure.
Typical Uses
These holders are handy for hobby electronics, student projects, small repairs and custom battery packs where a compact two-cell holder is needed. The back-to-back shape works well in slim boxes, model builds and other tight spaces. Because the pack includes two holders, you can keep one as a spare or use both in a single project.
What's in the Box
The pack contains two 2x AA back-to-back battery holder cases with wires.
Quick specs
- Item Type
- Battery Holder
- Compatibility
- AA Battery
- Width (mm)
- 25
- Wire Length (mm)
- 140
- Weight (g)
- 5(each)
- Shipping Weight
- 0.02 kg













