Skip to main content

Worldwide Shipping · Secure Payments

At a glance

This digital lcr meter is a good fit for DIY builders and repair work. Main specs: model no. / name Transistor Tester; microcontroller ATmega328 microcontroller; display 2x16 character LCD. Check that your power source supplies 3.7 V before connecting it.

Key Highlights

  • Model No. / Name: Transistor Tester
  • Microcontroller: ATmega328 microcontroller
  • Display: 2x16 character LCD

Ideal For

  • Everyday use

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Model No. / NameTransistor Tester
MicrocontrollerATmega328 microcontroller
Display2x16 character LCD
Shutdown Current20nA
Power Supply Voltage (V)3.7 V
Measurement RangeCapacitance 25pf to 100mF (100000 U F)
ResistanceRange 0.1 ohms - 50M ohms.
Inductance0.01MH-20H
Shipping Weight0.05 kg
Shipping Dimensions13 × 10 × 4 cm

Overview

The 3.7V Version of Inductor Capacitor ESR Meter DIY MG328 Multifunction Transistor Tester is listed in our digital lcr meter range and suits DIY builders and repair work. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Model No. / Name: Transistor Tester
  • Microcontroller: ATmega328 microcontroller (look up this chip to confirm it runs the firmware or libraries you plan to use)
  • Display: 2x16 character LCD (measured diagonally; compare with the space you have before ordering)
  • Shutdown Current: 20nA (your supply must deliver at least this much current)
  • Power Supply Voltage (V): 3.7 V (match this to your power supply; too high a voltage can damage the part)
  • Measurement Range: Capacitance 25pf to 100mF (100000 U F) (quoted range is usually line-of-sight; walls and interference shorten it)
  • Resistance: Range 0.1 ohms - 50M ohms. (quoted range is usually line-of-sight; walls and interference shorten it)
  • Inductance: 0.01MH-20H

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

The 3.7V version of the Inductor Capacitor ESR Meter DIY MG328 Multifunction Transistor Tester is a versatile and compact electronic testing tool designed for electronics enthusiasts and hobbyists. This device is equipped with advanced features to facilitate the measurement and analysis of various electronic components, including inductors, capacitors, and transistors. Caution: Short the three test terminals and enter the test, the screen prompts for the correction procedure. When prompted to disconnect the calibration time short end off the three tests will continue, when prompted to access 100nF capacitors on pins 1-3 over time, access to power distribution 1u F calibration capacitors after the program will automatically enter the next step. Until the end of the calibration restart to complete the calibration.

Features:

  1. 1. One-button measurement operation with automatic switch-off delay. Shutdown current is only 20nA and battery operation is supported. 2. Automatic detection of PNP and NPN bipolar triodes, N and P-channel MOSFETs, JFET field effect tubes, diodes, diodes, thyristors, resistors, capacitors, and inductors. Automatic detection of pin definitions. 3. Measurement of the current amplification factor (B) and the on-state voltage (U f) of the emitter junction for bipolar transistors. The amplification of Darlington transistors can be identified by high threshold voltages and high currents. 4. It detects the internal protection diodes of bipolar transistors and MOSFETs and displays them on the screen. 5. It measures the threshold voltage and gate capacitance of MOSFETs. 6. It supports two resistance measurements and can measure potentials. If the potentiometer is set to the end, the tester cannot distinguish between the middle and the two ends of the pin. 7. Resistance measurement resolution is 0.1 Ohm, maximum measurement 50M Ohm value. 8. Capacitance measurement ranges from 25pf to 100mF (100000 U F). Resolution up to 1pF, inductance measurement range 0.01MH-20H, otherwise it will be displayed as resistance, inductance DC resistance will also be displayed as resistance if Ou2100 is high. 9. Can detect the equivalent series resistance of capacitors above 2U F with a resolution of 0.01 ohms. This feature is very important for the detection of capacitor performance. 10. It can display the sign of two diodes in the correct direction and can also display the forward voltage drop. 11. The LED detects diodes with a higher-than-normal forward voltage drop. The double LED detection is a double diode. Simultaneous detection of the light-emitting diodes will flash. 12. Each test takes about two seconds, only measurements of large capacitors and inductors take a long time.

Package Includes:

1 x Tester (Batteries Not Included) 3pcs x High Quality Test Clips

Quick specs

Model No. / Name
Transistor Tester
Microcontroller
ATmega328 microcontroller
Display
2x16 character LCD
Shutdown Current
20nA
Power Supply Voltage (V)
3.7 V
Measurement Range
Capacitance 25pf to 100mF (100000 U F)
See all specifications