
1 / 3 · Click to enlarge
AI Summary
A compact 4-in-1 ESC rated at 35A per channel for 2S to 5S LiPo builds, running BLHeli_S firmware with DSHOT, OneShot and Multishot support. Its 20 x 20mm M2 mounting and integrated four-channel layout cut wiring and weight in small FPV frames.
Key Highlights
- Four integrated 35A speed controllers on one compact board
- Runs BLHeli_S firmware with JH-30 and JH-25 target support
- Supports DSHOT150, DSHOT300, DSHOT600, OneShot and Multishot
- 2S to 5S LiPo input range for flexible build options
- 20 x 20mm M2 mounting fits tight frames
- No BEC onboard, so a separate 5V supply is needed
Ideal For
- FPV racing pilots building compact quads
- Freestyle pilots who want a tidy 4-in-1 power stage
- Builders upgrading from four separate ESCs
- Makers working with 2S to 5S LiPo platforms
- Pilots using DSHOT or Multishot flight controllers
Buying Tip
Confirm your frame uses 20 x 20mm M2 mounting and that your build includes a separate 5V supply, since this ESC has no BEC.
Elecvora expert review
Our verdict
A sensible four-in-one ESC for compact FPV builds that need 35A channels and a small mounting footprint. It rewards buyers who plan for the missing BEC and verify their protocol support up front.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Four 35A channels on one compact board
- Broad protocol support including DSHOT600
- Small 20 x 20mm M2 mounting pattern
- BLHeli_S firmware with stated target
- Efficiency features such as synchronous rectification
Cons
- No BEC, so a separate 5V supply is required
- Requires soldering and firmware configuration
- Package contents are not specified
Best for
Compact FPV and racing quad builds with 2S to 5S packs
Not ideal for
Builds that need an onboard BEC or plug-and-play installation
Specifications
| Item Type | Electronic Speed Controller |
|---|---|
| Working Current (mA) | 35A |
| BEC (Y/N) | NO |
| Firmware | BLHeli S |
| Firmware Target | JH-30 JH-25 |
| Protocol Support | ONESHOT125, ONESHOT42, MULTISHOT, DSHOT150, DSHOT300, DSHOT600 |
| Mounting Style | : 20 x 20mm, M2 |
| Shipping Weight | 0.006 kg |
| Shipping Dimensions | 11 × 7 × 1 cm |
Frequently Asked Questions
What battery voltage does this ESC support?
Does it have a built-in BEC?
Which protocols can it use?
What firmware does it run?
What mounting pattern does it use?
What is included in the package?
Overview
This module combines four 35A electronic speed controllers into a single board, giving compact quadcopters a cleaner power stage than four separate ESCs. The 4-in-1 layout reduces the number of wires running through the frame and keeps the stack low, which matters in small FPV and racing builds. It accepts 2S to 5S LiPo input and runs BLHeli_S firmware with a JH-30 JH-25 target.
Key Features
- Four channels in one board: each channel is rated for 35A working current.
- BLHeli_S firmware: firmware target JH-30 JH-25 for this module.
- Wide protocol support: ONESHOT125, ONESHOT42, MULTISHOT, DSHOT150, DSHOT300 and DSHOT600.
- Compact footprint: 20 x 20mm M2 mounting pattern for tight frames.
- Efficiency features: adaptive timing, synchronous rectification and damped light.
- No BEC: a separate 5V supply is required for the flight controller and peripherals.
Specifications Explained
35A working current describes the continuous current rating per channel. Match your motors and propellers so the expected current stays within this figure. 2S to 5S input covers a broad range of LiPo packs, from lightweight 2S setups to 5S racing configurations. BLHeli_S is a widely used ESC firmware family, and the stated JH-30 JH-25 target tells you which firmware build applies to this board. Protocol support means the ESC can receive throttle commands from a compatible flight controller using any of the listed digital or analog protocols, with DSHOT600 offering the fastest update rate among them. 20 x 20mm M2 mounting defines the hole spacing and screw size, so check your frame and stack before ordering. The absence of a BEC means the board does not supply 5V power.
Compatibility and Requirements
Use a flight controller that supports one of the listed protocols: ONESHOT125, ONESHOT42, MULTISHOT, DSHOT150, DSHOT300 or DSHOT600. The board requires a 2S to 5S LiPo pack and a separate 5V supply because no BEC is built in. Mounting requires 20 x 20mm spacing with M2 screws. Confirm motor current draw stays within the 35A per-channel rating.
Typical Uses
This ESC suits compact quadcopters, FPV racing builds and small freestyle frames where weight and wiring simplicity matter. It is also useful for rebuilds where a single board replaces four separate ESCs.
What's in the Box
Package contents are not specified by the manufacturer. Check the listing details before ordering if you need to confirm included accessories.
Quick specs
- Item Type
- Electronic Speed Controller
- Working Current (mA)
- 35A
- BEC (Y/N)
- NO
- Firmware
- BLHeli S
- Firmware Target
- JH-30 JH-25
- Protocol Support
- ONESHOT125, ONESHOT42, MULTISHOT, DSHOT150, DSHOT300, DSHOT600













