
1 / 6 · Click to enlarge
AI Summary
A shield module that adds 4G LTE, GNSS positioning and BLE 5.0 connectivity to Arduino and Raspberry Pi builds. It works over USB as a standalone unit or over UART with your microcontroller, so tracking and IoT projects get cellular data plus location in one board.
Key Highlights
- 4G/3G/2G cellular connectivity with VoLTE support and LTE-CAT1 speed option
- GNSS positioning with onboard GPS patch antenna for location-aware projects
- BLE 5.0 radio with printed PCB antenna and optional external antenna connector
- USB interface for standalone use with Windows, Linux or Android hosts
- UART interface for Arduino UNO and other microcontroller platforms
- Four-layer PCB with impedance matching for external LTE and BLE antennas
Ideal For
- Arduino UNO makers building connected IoT devices
- Raspberry Pi developers adding cellular and GNSS to a project
- IoT and tracking prototypers who need 4G data plus location
- Field sensor builders reporting remotely over cellular networks
- Makers experimenting with BLE 5.0 alongside GNSS
Buying Tip
Check that your project can supply a stable USB +5V source within plus or minus 5 percent before wiring the shield, since cellular transmission draws more current than a small board alone.
Elecvora expert review
Our verdict
This is a tidy multi-radio shield that puts cellular data, GNSS and BLE 5.0 on one board with both USB and UART paths. It is a sensible starting point for tracking and IoT prototypes rather than a finished product.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Cellular, GNSS and BLE 5.0 on a single board
- USB standalone mode plus UART for microcontrollers
- Broad protocol support including MQTT and HTTPS
- Four-layer PCB with impedance matching for external antennas
- Firmware updates over USB or FOTA
Cons
- Requires a stable USB +5V supply within plus or minus 5 percent
- External antennas for LTE and BLE are not included
- Optional sensors and secure element are not populated
Best for
Makers building connected tracking and IoT prototypes
Not ideal for
Users wanting a plug-and-play finished tracker with no wiring
Specifications
| Item Type | Shield Module |
|---|---|
| Additional Specs. | Connectivity Support: 4G/3G/2G/VoLTE |
| Operating Voltage | USB +5V ± 5% |
| Module | GNSS positioning module, LTE-CAT1 speed option |
| Length (mm) | 11 |
| Width (mm) | 53 |
| Weight (g) | 35 |
| Shipping Weight | 0.035 kg |
| Shipping Dimensions | 17 × 10 × 3 cm |
What's in the box
- 1 x 4G LTE Shield with GNSS and BLE 5.0
Frequently Asked Questions
Can I use this shield without an Arduino?
Which Arduino boards is it compatible with?
What power supply does it need?
Does it include GNSS and BLE antennas?
What is in the package?
Can the firmware be updated?
Overview
This shield module combines cellular communication, satellite positioning and Bluetooth Low Energy on one board. It is built around a GNSS positioning module with an LTE-CAT1 speed option, and it supports 4G, 3G and 2G networks including VoLTE. The board is designed to sit directly on an Arduino UNO, and the same hardware can be used with a Raspberry Pi or another microcontroller through its UART interface.
Because the USB interface turns the board into a standalone unit, you can also connect it to a Windows, Linux or Android host without any microcontroller attached. That makes it a practical building block for IoT nodes, tracking devices and connected sensor projects.
Key Features
- Cellular data: 4G, 3G and 2G connectivity with VoLTE support and LTE-CAT1 speed.
- GNSS positioning: onboard GPS patch antenna for location data.
- BLE 5.0: printed PCB antenna plus an optional connector for an external antenna.
- Dual interface: USB for standalone host use, UART for Arduino and other microcontrollers.
- RF-focused design: four-layer PCB and impedance matching for external LTE and BLE antennas.
- Protocol support: mail, TCP/IP, IPv4 and IPv6 multi-PDP, MT PDP, FTP, FTPS, HTTP, HTTPS, MQTT and DNS.
- Firmware updates: available over USB or FOTA.
Specifications Explained
The operating voltage is USB +5V with a tolerance of plus or minus 5 percent, so the board expects a stable USB-style supply. The module measures 53 mm wide and 11 mm long, with a weight of 35 g, which keeps it light enough for small enclosures and portable builds.
The GNSS positioning module gives you satellite-based location, while the LTE-CAT1 option describes the cellular speed class rather than a maximum throughput figure. VoLTE support means voice over LTE is part of the cellular feature set. The BLE 5.0 radio is paired with a printed PCB antenna, and impedance matching leaves room to switch to external antennas for BLE and LTE when your enclosure or range needs call for it.
Compatibility and Requirements
The shield is designed to be directly compatible with Arduino UNO. It also connects to other microcontroller platforms through UART, and to Windows, Linux or Android hosts through USB as a standalone unit. Power comes from USB +5V plus or minus 5 percent. An external antenna can be fitted for LTE and BLE where the board's connectors and impedance matching allow.
Typical Uses
- IoT nodes that need cellular backhaul and location data.
- Asset and vehicle tracking prototypes.
- Remote sensor installations that report over 4G.
- Arduino and Raspberry Pi projects that combine GNSS with BLE.
- Standalone USB-connected cellular and positioning setups on a PC.
What's in the Box
1 x 4G LTE Shield with GNSS and BLE 5.0.
Quick specs
- Item Type
- Shield Module
- Additional Specs.
- Connectivity Support: 4G/3G/2G/VoLTE
- Operating Voltage
- USB +5V ± 5%
- Module
- GNSS positioning module, LTE-CAT1 speed option
- Length (mm)
- 11
- Width (mm)
- 53













