Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact 330uH surface mount power inductor with a shielded ferrite drum core, rated at 1.3A with 360mΩ DC resistance. Its small 9 x 8mm footprint suits dense DC-DC converter and power supply layouts.

Key Highlights

  • 330uH inductance with 30 percent tolerance for power conversion circuits
  • Shielded ferrite drum core helps limit magnetic interference
  • 1.3A current rating with low 360mΩ DC resistance
  • Compact 9 x 8mm SMD footprint weighing about 1g
  • Rated for 100kHz operation from -40 to 100 degrees Celsius
  • Surface mount pads for straightforward reflow soldering

Ideal For

  • Electronics designers building compact DC-DC converter circuits
  • Repair technicians replacing failed SMD power inductors
  • Hobbyists and makers prototyping power supply boards
  • Students learning surface mount power component selection

Buying Tip

Check your circuit's peak current against the 1.3A rating and confirm your board has SMD pads sized for a 9 x 8mm part before ordering.

Elecvora expert review

Our verdict

A sensible compact choice for low-to-moderate current power conversion where shielding and small size matter. The wide 30 percent tolerance and 1.3A ceiling mean it suits general designs rather than precision or high-current work.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Shielded ferrite drum core reduces magnetic interference
  • Compact 9 x 8mm footprint for dense boards
  • Low 360mΩ DC resistance limits resistive losses
  • Wide -40 to 100 degrees Celsius operating range

Cons

  • 30 percent tolerance is wider than precision applications allow
  • 1.3A rating limits use in higher-current designs
  • Surface mount only, so reflow or careful hand soldering is required

Best for

Compact DC-DC converter and power filtering builds in portable electronics

Not ideal for

High-current power stages or circuits needing tight inductance tolerance

Specifications

Inductance330uH
Mounting TypeSMD/SMT
Core MaterialFerrite
Tolerance (%)30
Current Rating (A)1.3
Frequency (kHz)100
Operating Temperature (°C)-40 to 100
Length (mm)9
Width (mm)8
Weight (g)1 (approx) (each)
DC Resistance (mΩ)360
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

What's in the box

  • 1 x 330uH 2A SMD power inductor

Frequently Asked Questions

What is this inductor used for?
It is a surface mount power inductor intended for DC-DC converters, power supply filtering and similar tasks in compact electronics such as phones, media players and cameras.
Can I solder it by hand?
Yes, but it is a surface mount part, so you need fine soldering tools and care to avoid overheating the body. Reflow soldering is the more typical method.
What current can it handle?
The rated current is 1.3A, with a DC resistance of 360mΩ. Keep your circuit's current within that figure to avoid overheating.
Does it come with mounting hardware?
No. The order includes one inductor only, with no additional hardware or accessories.
What is the operating temperature range?
It is rated from -40 to 100 degrees Celsius, which covers most indoor electronic environments.
Is the inductance value exact?
No. The tolerance is 30 percent, so the actual value can vary within that band around 330uH, which is normal for power inductors.

Overview

The 8D43 330uH SMD power inductor is a surface mount component designed for power conversion and filtering duties on compact circuit boards. It uses a ferrite drum core with a magnetic shield, a construction that helps contain the magnetic field and reduce interference with nearby parts. At roughly 9mm long, 8mm wide and about 1g in weight, it is small enough for densely populated designs while still offering a useful 330uH inductance value.

Key Features

  • Ferrite drum core with magnetic shielding
  • Surface mount pads for reflow soldering
  • 330uH inductance at 30 percent tolerance
  • 1.3A current rating and 360mΩ DC resistance
  • Compact 9 x 8mm body weighing about 1g
  • Operating range of -40 to 100 degrees Celsius

Specifications Explained

Inductance and tolerance: 330uH with a 30 percent tolerance means the actual value can sit within a fairly wide band around the nominal figure. This is common for power inductors and is usually acceptable in DC-DC conversion and filtering, where exact values matter less than stable energy storage.

Current and resistance: The 1.3A current rating defines the load the part is intended to handle, while the 360mΩ DC resistance indicates how much resistive loss appears in the winding. Lower resistance means less heating under load, which matters in compact enclosures.

Frequency and temperature: The inductor is rated at 100kHz, so it suits switching circuits operating around that frequency. Its -40 to 100 degrees Celsius range covers most indoor electronics environments.

Compatibility and Requirements

This is a surface mount part, so it requires a PCB with matching SMD pads and a reflow soldering process or careful hand soldering with suitable tools. It is not a through-hole component. Confirm that your circuit's current draw stays within the 1.3A rating and that your switching frequency is appropriate for a 100kHz-rated inductor before fitting.

Typical Uses

Designers and technicians commonly use parts like this as DC-DC converter inductors in mobile phones, portable media players, PDAs, hard disk drives and digital camera or camcorder hardware. It also works well for general power supply filtering and repair work where a compact shielded inductor is needed.

What's in the Box

One 330uH 2A SMD power inductor is included. No other accessories or mounting hardware are supplied.

Quick specs

Inductance
330uH
Mounting Type
SMD/SMT
Core Material
Ferrite
Tolerance (%)
30
Current Rating (A)
1.3
Frequency (kHz)
100
See all specifications