Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 9x12mm through-hole power inductor with 100uH inductance and a 1.2A current rating. Its 0.16mΩ DC resistance keeps losses low in DC/DC and general-purpose filtering circuits.

Key Highlights

  • 100uH inductance with a 10% tolerance for predictable filtering
  • 1.2A current rating suits small DC/DC and VRM stages
  • Low 0.16mΩ DC resistance helps limit conduction losses
  • Through-hole DIP leads for secure, rework-friendly mounting
  • Compact 9 x 12mm body fits space-limited boards
  • Rated for operation from -40 to 85 degrees Celsius

Ideal For

  • Electronics hobbyists building through-hole prototype boards
  • Repair technicians replacing a radial 100uH choke
  • Design engineers working on DC/DC converter stages
  • Students learning about inductors and filtering circuits
  • Makers maintaining VRM and distributed power boards

Buying Tip

Check the lead spacing and board hole pattern against the 9 x 12mm body before ordering, and confirm your circuit current stays below the 1.2A rating.

Elecvora expert review

Our verdict

A tidy, no-fuss through-hole inductor that covers the common 100uH, 1.2A role on small power boards. The low DC resistance and compact body make it easy to work with during prototyping and repair.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Clear 100uH value with a tight 10% tolerance
  • Low 0.16mΩ DC resistance
  • Through-hole leads are easy to solder and rework
  • Compact 9 x 12mm body
  • Wide -40 to 85 degrees Celsius operating range

Cons

  • 1.2A rating limits it to lower-current designs
  • Single unit only, so spares must be ordered separately
  • Through-hole mounting is not suited to surface-mount-only boards

Best for

Through-hole prototyping, repair and small DC/DC filtering work

Not ideal for

High-current power stages or surface-mount-only assemblies

Specifications

Inductance100uH
Tolerance (%)10
Mounting TypeThrough Hole
Current Rating (A)1.2
Frequency (Hz)1000
Operating Temperature (°C)-40 to 85
Length (mm)9
Width (mm)12
Weight (g)1 (approx) (each)
DC Resistance(mΩ)0.16
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

What's in the box

  • 1 x 9x12mm 100uH DIP Power Inductor

Frequently Asked Questions

What is the inductance of this inductor?
It is 100uH with a tolerance of 10%, so each unit sits close to that nominal value.
How much current can it handle?
The current rating is 1.2A. Design your circuit so the expected current stays below that figure.
How does it mount to a board?
It is a through-hole part. The leads pass through plated holes and are soldered on the underside of the board.
What is the DC resistance?
The DC resistance is 0.16mΩ, which keeps series losses low at the rated current.
What is included when I order?
You receive one 9x12mm 100uH DIP power inductor, weighing approximately 1g.
What temperature range does it support?
It is rated to operate between -40 and 85 degrees Celsius, which covers typical indoor and enclosed equipment conditions.

Overview

The 9x12mm 100uH DIP power inductor is a radial, through-hole choke coil built for filtering and energy storage on small power boards. It measures 9mm by 12mm, carries a 100uH inductance with a 10% tolerance, and is rated for 1.2A. With a DC resistance of just 0.16mΩ, it adds very little series resistance to the circuit it sits in.

This is a single inductor aimed at people who build, repair or prototype through-hole electronics. It is a straightforward part: two leads, a wound core, and a compact body that sits neatly on a board without needing a surface-mount footprint.

Key Features

  • 100uH inductance: a useful mid-range value for smoothing and choke duties.
  • 1.2A current rating: a clear working limit for current planning.
  • 0.16mΩ DC resistance: low series loss at the rated current.
  • Through-hole mounting: leads pass through the board for a firm mechanical joint.
  • 9 x 12mm body: compact enough for dense layouts.
  • -40 to 85 degrees Celsius range: covers typical indoor and enclosed equipment conditions.

Specifications Explained

Inductance and tolerance. At 100uH with a 10% tolerance, the part will sit within a narrow band around its nominal value. That matters when the circuit is tuned around a specific inductance, because a tighter spread means less variation between units.

Current rating. The 1.2A figure is the practical ceiling to design around. Keep the expected current below this value so the inductor is not pushed beyond its intended operating point.

DC resistance. At 0.16mΩ, the winding contributes very little resistance in series with the load, which keeps voltage drop and heating low.

Frequency and temperature. The listed frequency figure is 1000Hz, and the part is rated to operate between -40 and 85 degrees Celsius, so it suits ordinary room-temperature and enclosed-equipment environments.

Compatibility and Requirements

This is a through-hole component, so the board must have plated holes spaced to match the lead pitch of the 9 x 12mm body. It requires soldering to the PCB. No other accessories are needed to mount it, and no mating parts are supplied.

Typical Uses

Common applications include DC/DC converter stages in distributed power systems, VRM circuits, and general-purpose filtering where a leaded choke is preferred. It is also a sensible spare for repair work on boards that already use a radial 100uH inductor.

What's in the Box

One 9x12mm 100uH DIP power inductor. Each unit weighs approximately 1g.

Quick specs

Inductance
100uH
Tolerance (%)
10
Mounting Type
Through Hole
Current Rating (A)
1.2
Frequency (Hz)
1000
Operating Temperature (°C)
-40 to 85
See all specifications