Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A matched male and female 8mm bullet connector pair from Amass with silver plated contacts and flame-retardant housing caps. Rated to 150A continuous at DC500V, it gives high-power RC and drone builds a secure, low-resistance battery link for 6AWG wiring.

Key Highlights

  • 8mm bullet design with silver plated contacts for low-resistance power transfer
  • Rated up to 150A continuous current at DC500V
  • Flame-retardant composite housing with protective cap
  • Accepts 6AWG wire for heavy-duty battery leads
  • Secure fitting helps maintain stable conductivity under load
  • Soldered installation for a permanent, serviceable joint

Ideal For

  • Drone builders running high-current battery harnesses
  • RC airplane pilots using large LiPo packs
  • Heavy-lift multirotor and payload platforms
  • Makers building custom high-power distribution
  • Hobbyists replacing worn connectors on existing rigs

Buying Tip

Check that your battery leads are 6AWG and that your soldering setup can heat an 8mm bullet before you commit, since a cold joint on a 150A connector is a real weak point.

Elecvora expert review

Our verdict

The SH8.0 is a purpose-built high-current connector that does exactly what its ratings promise, provided you solder it properly. It is a sensible choice for large packs and heavy power trains where smaller connectors would run hot.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • 150A continuous and DC500V ratings suit serious power systems
  • Silver plated 8mm contacts support stable conductivity
  • Flame-retardant housing with cap adds protection
  • Matched male and female pair with 6AWG support

Cons

  • Requires soldering and a heat source strong enough for 8mm bullets
  • Only one pair per pack, so multi-battery setups need extra sets
  • Bulky size is unnecessary for low-current builds

Best for

High-current drone, RC aircraft and custom power harnesses

Not ideal for

Small low-draw electronics or solder-free plug-and-play setups

Specifications

Shipping Weight0.02 kg
Shipping Dimensions10 × 8 × 2 cm

What's in the box

  • 1 x Amass SH8.0 Silver Plated Bullet Battery Connector Pair with Housing Cap - SH8.0-F.S.B & SH8.0-M.S.R

Frequently Asked Questions

What current can this connector handle?
The pair is rated for up to 150A continuous current with a DC500V voltage rating. Keep your wiring and soldering quality in line with that load.
What wire size should I use?
Amass specifies 6AWG wire for the SH8.0. Using thinner wire adds resistance and limits the benefit of the connector.
Do I need to solder it?
Yes. These are solder-type bullet connectors, so you need a soldering iron or torch able to heat an 8mm bullet and thick 6AWG wire.
What exactly is included?
One pair: the SH8.0-F.S.B female and SH8.0-M.S.R male connector with a housing cap. Additional pairs are needed for extra battery packs.
Is it compatible with my drone or RC model?
It suits RC model batteries, airplanes, drones and high-power systems that use 8mm bullets and 6AWG leads. Check your existing connector size before ordering.
How should I look after the connectors?
Keep the housing cap on when disconnected, inspect the contacts for corrosion or damage, and re-solder rather than bending a deformed bullet.

Overview

The Amass SH8.0 is a matched battery connector pair made for setups that move a lot of current. Each connector uses an 8mm bullet contact finished in silver plating, held inside a flame-retardant composite housing and supplied with a housing cap. The male and female halves mate together to form a compact, shrouded power junction that resists accidental contact and keeps the connection stable in vibration-heavy applications.

This is hardware for builders who solder their own leads. With a 150A continuous rating, a DC500V voltage rating and support for 6AWG wire, the SH8.0 sits in the high-power tier of RC connectors rather than the small-signal end.

Key Features

  • 8mm bullet contacts: a generous contact area for high-current paths.
  • Silver plating: supports stable conductivity at the mating surface.
  • 150A continuous rating: suited to demanding RC and power systems.
  • DC500V rating: covers the voltage ranges used in large battery packs.
  • Flame-retardant composite housing: adds a protective layer around the contact.
  • 6AWG compatibility: matches thick battery leads.
  • Housing cap included: shields the connector when not in use.

Specifications Explained

Current and voltage

The 150A continuous figure describes the load the connector is designed to carry over time, while the DC500V rating sets the voltage ceiling. Together they tell you this pair belongs on large packs and high-draw power trains, not on small receivers or light accessories.

8mm bullet and silver plating

Bullet size determines how much metal meets metal at the joint. At 8mm, the SH8.0 offers a substantial contact surface, and the silver plating is there to keep that surface conductive and consistent through repeated mating cycles.

Wire gauge

The connector is intended for 6AWG wire. Using a wire that is too thin for your current draw adds resistance before the power even reaches the connector, so match your leads to the 6AWG recommendation.

Housing material

The flame-retardant composite shell surrounds the bullet and provides mechanical protection plus a keyed, cap-covered interface. It also reduces the chance of an accidental short when the pair is disconnected.

Compatibility and Requirements

The SH8.0 pair is designed for 6AWG wire and soldered termination. You will need a soldering iron or torch capable of heating a large bullet and thick wire, plus suitable heat shrink and a way to secure the leads. The connectors are intended for RC model batteries, airplanes, drones and other high-power systems. Because the pair is sold as a set of one male and one female connector with a housing cap, plan your harness around a single battery-to-device link or order additional pairs for extra packs.

Typical Uses

  • Battery leads on large-capacity LiPo packs
  • Heavy-lift multirotor and drone power harnesses
  • RC airplane and fixed-wing power systems
  • High-current power distribution in custom builds
  • Replacing worn or undersized connectors on an existing high-power setup

What's in the Box

1 x Amass SH8.0 Silver Plated Bullet Battery Connector Pair with Housing Cap - SH8.0-F.S.B & SH8.0-M.S.R.

Quick specs

Shipping Weight
0.02 kg
Shipping Dimensions
10 × 8 × 2 cm
See all specifications