
1 / 3 · Click to enlarge
AI Summary
This power module provides a regulated 5.3V, 3A supply to APM/Pixhawk flight controllers and measures battery voltage and current up to 90A. It connects inline with your LiPo via XT60 connectors and a 6-position cable.
Key Highlights
- Regulated 5.3V output at up to 3A for flight controller and accessories
- Integrated voltage and current sensing up to 90A
- XT60 connectors for easy inline installation with LiPo batteries
- 6-position cable plugs directly into APM/Pixhawk PM port
- Supports 2S to 6S LiPo batteries
- Compact and lightweight at only 24g
Ideal For
- APM/Pixhawk users needing reliable power and monitoring
- Multirotor builders using 2S-6S LiPo batteries
- Fixed-wing pilots wanting battery voltage and current data
- FPV enthusiasts upgrading their power system
- DIY drone makers seeking a compact BEC solution
Buying Tip
Verify that your flight controller has a PM port and that your battery uses XT60 connectors; if not, you may need adapters.
Elecvora expert review
Our verdict
This power module offers a straightforward way to power APM/Pixhawk controllers and monitor battery usage. It is a reliable, no-fuss solution for basic power needs.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Simple plug-and-play installation with XT60 connectors
- Provides both regulated power and current/voltage sensing
- Compact and lightweight design
Cons
- Not designed to power servos, requiring a separate BEC for servo power
- Limited to APM and Pixhawk controllers with a PM port
- Current sensing may require calibration for accurate readings
Best for
APM/Pixhawk users needing a compact power and monitoring solution
Not ideal for
Systems requiring servo power from the BEC or non-APM/Pixhawk controllers
Specifications
| Connector Type | XT60 |
|---|---|
| Length (cm) | 160 |
| Weight (g) | 24 |
| Shipping Weight | 0.027 kg |
| Shipping Dimensions | 15 × 5 × 2 cm |
What's in the box
- 1 x APM/Pixhawk Power Module Output BEC 3A XT60 Connector 28V 90A
Frequently Asked Questions
Can this module power my servos?
What batteries are supported?
Does it come with cables?
What is the maximum current output?
Is the current sensor calibrated?
Can I use this with a Pixhawk 4?
Overview
The Generic APM/Pixhawk Power Module is an essential component for anyone building or maintaining an APM or Pixhawk-based flight controller setup. It serves two key roles: it provides a stable 5.3V power supply to the flight controller and connected accessories, and it measures the battery voltage and current consumption, feeding this data back to the controller for monitoring and failsafe actions. The module is designed to be connected inline between your LiPo battery and the rest of the power system using XT60 connectors, and it communicates with the flight controller through a 6-position cable that plugs directly into the PM port.
Key Features
- Regulated 5.3V output: The on-board switching regulator delivers up to 3A, providing clean power to the flight controller, receiver, GPS, and telemetry radio.
- Voltage and current sensing: The module measures battery voltage and current draw up to 90A, allowing the flight controller to display real-time power data and trigger low-voltage warnings.
- XT60 connectors: Pre-fitted XT60 connectors make it easy to integrate the module into your power chain without soldering.
- Wide battery compatibility: Works with 2S to 6S LiPo batteries, covering a broad range of models from small multirotors to larger fixed-wing aircraft.
- Plug-and-play connection: The included 6-position cable connects directly to the PM port of APM 2.5.2/2.6/2.8 and Pixhawk flight controllers.
Specifications Explained
Output voltage and current: The 5.3V output is tailored for the flight controller and its low-power peripherals. With a 3A maximum, it can comfortably power the controller, an RC receiver, a GPS module, and a telemetry radio, but it is not intended to drive servos. For servo power, you should rely on your aircraft's ESC/BEC.
Current sensing range: The 90A sensing capability means the module can monitor current draw in high-power setups, giving you accurate consumption data for battery management and performance analysis.
Connector type: XT60 connectors are widely used in RC hobbies and provide a secure, low-resistance connection. The module's length of 160 cm (including cable) offers flexibility in mounting, and its 24g weight adds negligible load to your aircraft.
Compatibility and Requirements
This power module is designed specifically for APM 2.5.2, 2.6, 2.8, and Pixhawk flight controllers. It requires a 2S to 6S LiPo battery and connects via XT60 connectors. The 6-position cable plugs into the PM port on the flight controller. Note that the module is not designed to power servos; use your ESC's built-in BEC for that purpose. The actual product version printed on the module may vary.
Typical Uses
This module is ideal for multirotor and fixed-wing aircraft running APM or Pixhawk controllers. It is commonly used in FPV builds, aerial photography platforms, and autonomous drones where reliable power and battery monitoring are essential. Whether you are building a new model or upgrading an existing one, this module simplifies wiring and provides critical power data.
What's in the Box
Package includes: 1 x APM/Pixhawk Power Module Output BEC 3A XT60 Connector 28V 90A.
Quick specs
- Connector Type
- XT60
- Length (cm)
- 160
- Weight (g)
- 24
- Shipping Weight
- 0.027 kg
- Shipping Dimensions
- 15 × 5 × 2 cm













