
1 / 4 · Click to enlarge
AI Summary
A compact bidirectional ESC with a 2-6S input range, 5A continuous and 50A peak current, plus a 5V UBEC output. Its 1:1 forward and reverse power delivery means direct reversing with no throttle calibration needed.
Key Highlights
- Bidirectional 1:1 power output for direct reverse without a brake
- 2-6S input range with 50A peak and 5A continuous current
- Integrated 5V UBEC output for receiver and servo power
- PWM input accepts 1000-2000us signals from common radios
- Overcurrent and overheat protection for demanding runs
- Compact, lightweight board that fits tight chassis and hulls
Ideal For
- RC car builders who want immediate reverse without a brake sequence
- Model boat hobbyists manoeuvring in confined water
- Underwater thruster projects needing direct bidirectional drive
- Makers combining motor drive and 5V receiver power in one unit
- Hobbyists working with 2S to 6S battery packs
Buying Tip
Check that your battery is within the 2-6S range and your receiver outputs a 1000-2000us PWM throttle signal before soldering the controller into your build.
Elecvora expert review
Our verdict
A practical bidirectional controller for hobbyists who value direct reversing and a built-in 5V output over elaborate tuning. It is compact and simple to wire, though the 5A continuous rating means you should match it to modest drive setups.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 1:1 forward and reverse power with no brake delay
- Integrated 5V UBEC reduces extra components
- No throttle calibration needed
- Overcurrent and overheat protection
- Small, lightweight board
Cons
- Continuous current is limited to 5A
- No dimensions or weight for the bare board are listed
- Requires soldering power and motor connections
Best for
RC cars, boats and thrusters needing compact bidirectional drive
Not ideal for
High-current continuous drive setups beyond the 5A rating
Specifications
| Item Type | Electronic Speed Controller |
|---|---|
| PWM frequency | 1000-2000us |
| Peak Current (A) | 50 |
| Continuous Discharge Current (A) | 5 |
| Shipping Weight | 0.044 kg |
| Shipping Dimensions | 12 × 8 × 1 cm |
What's in the box
- 1 x Bidirectional 50A 2-6S UBEC 5A 5V electronic speed controller
Frequently Asked Questions
Do I need to calibrate the throttle before use?
What battery range does it support?
What is the difference between the 50A and 5A ratings?
Does it provide power for my receiver?
What signal does it expect from the radio?
What is included with the controller?
Overview
This bidirectional speed controller is designed for RC builds that need to drive forward and backward with equal authority. Instead of a brake-and-reverse sequence, it delivers 1:1 power in both directions, so the model responds immediately when the throttle is pulled back. The controller accepts 2-6S input and provides a 5V UBEC output alongside its motor drive, which simplifies wiring in cars, ships and underwater thrusters.
The design is plug-and-play in the sense that the throttle stroke does not need to be calibrated before use. Solder your motor and power leads, connect the signal wire to your receiver, and the controller is ready. Imported components and a full power test at the factory support consistent output.
Key Features
- True bidirectional drive: 1:1 power output in forward and reverse with no brake delay.
- Wide input range: Runs on 2S through 6S packs.
- Strong current headroom: 50A peak rating with 5A continuous discharge.
- Onboard 5V UBEC: Supplies receiver and servo power from the same unit.
- Protection built in: Overcurrent and overheat safeguards.
- Compact footprint: Small and light enough for cramped chassis and hulls.
Specifications Explained
Current ratings
The 50A peak figure covers short bursts of demand, such as hard acceleration or a sudden reverse. The 5A continuous discharge rating is the figure to plan around for steady running, so match your setup to avoid holding the controller at its peak for long periods.
Voltage and UBEC output
The 2-6S input range covers common hobby packs from small 2S batteries up to 6S. The 5V UBEC output lets the controller feed your receiver and servos, reducing the number of separate power components in the build.
PWM signal
The 1000-2000us PWM range is the standard throttle signal format used by many RC transmitters and receivers, so setup is familiar for most hobbyists.
Compatibility and Requirements
Use a 2-6S battery pack and a radio system that outputs a 1000-2000us PWM throttle signal. The controller is intended for brushed-style bidirectional drive in cars, ships and underwater thrusters. Because no throttle calibration is required, the main setup work is soldering the power and motor connections and plugging the signal lead into the receiver.
Typical Uses
This controller suits RC cars that need quick reversing, boats that manoeuvre in tight spaces, and underwater thrusters where direct reverse response matters. It is also useful in any project where a compact bidirectional driver with a 5V output is preferred over separate ESC and BEC units.
What's in the Box
- 1 x Bidirectional 50A 2-6S UBEC 5A 5V electronic speed controller
Quick specs
- Item Type
- Electronic Speed Controller
- PWM frequency
- 1000-2000us
- Peak Current (A)
- 50
- Continuous Discharge Current (A)
- 5
- Shipping Weight
- 0.044 kg
- Shipping Dimensions
- 12 × 8 × 1 cm













