
1 / 3 · Click to enlarge
AI Summary
A compact black plastic holder that seats two 18650 cells in series and brings out a 7.2V output through 15 cm solder-ready leads. It keeps your cells aligned and protected while leaving them easy to access, since there is no cover.
Key Highlights
- Holds two 18650 cells in a series configuration
- Moulded black plastic body measures 76 x 40 x 20 mm
- Pre-fitted leads roughly 15 cm long, ready to solder
- Delivers a 7.2V output when both cells are fitted
- Weighs only 14 g, so it adds little to your build
- Open, cover-free design keeps cells quick to swap
Ideal For
- DIY electronics builders making small two-cell packs
- Hobbyists building portable test gear and prototypes
- Makers who need removable 18650 power in a compact enclosure
- Workshop users organising and storing spare 18650 cells
- Model and gadget builders working with a 7.2V supply
Buying Tip
Measure your enclosure against the 76 x 40 x 20 mm body and confirm your circuit expects a 7.2V series supply before ordering, and remember the 18650 cells are not included.
Elecvora expert review
Our verdict
A no-frills holder that does one job well: it keeps two 18650 cells aligned and brings out a 7.2V series output on solder-ready leads. The open, cover-free format is a plus for anyone who swaps cells often, provided you are comfortable soldering.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Series wiring gives a ready 7.2V output
- Leads already attached, about 15 cm long
- Compact and light at 76 x 40 x 20 mm and 14 g
- Open design makes cell changes quick
Cons
- Cells are not included
- No cover, so cells are exposed to dust and knocks
- No on/off switch, so you must add your own
Best for
Small DIY builds and prototypes needing a removable two-cell 7.2V supply
Not ideal for
Users wanting a sealed, switch-equipped battery pack out of the box
Specifications
| Item Type | Battery Holder |
|---|---|
| Compatibility | 18650 Cell |
| Material | Plastic |
| Internal Connections | Series |
| Output Voltage | 7.2 |
| ON/OFF Switch | NO |
| Cable Length | 15 |
| Color | Black |
| Dimensions (L x W x H) mm | 76x40x20 |
| Weight (g) | 14 |
| Shipping Weight | 0.018 kg |
| Shipping Dimensions | 9 × 5 × 3 cm |
What's in the box
- 1 x Black plastic 2 x 18650 battery holder case, without cover
Frequently Asked Questions
Does this holder include the 18650 batteries?
What output voltage does it provide?
Do I need to solder anything?
Is there a cover or a switch?
What are the dimensions and weight?
How should I look after it?
Overview
This battery holder is a simple, well-formed plastic cradle for two 18650 cells. The cells sit side by side and are wired in series, so the holder presents a 7.2V output on its flying leads. Those leads measure about 15 cm, giving you enough length to route them to a switch, connector or circuit board before soldering. The body is black plastic, measuring 76 x 40 x 20 mm and weighing 14 g.
Because the holder ships without a cover, the cells remain visible and easy to reach. That suits builds where you want to check cell condition, swap cells between sessions or fit the holder into a tight space where a lid would add bulk.
Key Features
- Series wiring: two 18650 cells combine to give a 7.2V output.
- Solder-ready leads: approximately 15 cm of cable already attached.
- Compact footprint: 76 x 40 x 20 mm fits small enclosures.
- Lightweight: 14 g, so it barely affects the balance of a build.
- No switch: power control stays in your own circuit design.
- Open design: no cover, so cells are simple to insert and remove.
Specifications Explained
Series connection and 7.2V output
Series wiring means the two cells are linked end to end rather than in parallel. With two 18650 cells fitted, the holder's output is 7.2V, which suits devices and projects designed to run from a two-cell pack. Plan your circuit around that figure.
Lead length
The attached cable is about 15 cm long. That is enough to reach a nearby switch or connector without needing extra wire, though longer runs will need your own extension.
Size and weight
At 76 x 40 x 20 mm and 14 g, the holder is small and light. Check the internal space of your enclosure against these figures before committing to a layout.
Compatibility and Requirements
The holder is built for 18650 cells, which are not included and must be purchased separately. It has no on/off switch, so any switching or protection must come from your own wiring. Soldering is required to connect the leads to your circuit.
Typical Uses
This holder suits small DIY electronics projects, portable test gear, handheld devices, model and hobby builds, and workshop prototypes that need a removable two-cell power source. It is also handy as a tidy way to store and organise spare 18650 cells between uses.
What's in the Box
- 1 x Black plastic 2 x 18650 battery holder case, without cover
Quick specs
- Item Type
- Battery Holder
- Compatibility
- 18650 Cell
- Material
- Plastic
- Internal Connections
- Series
- Output Voltage
- 7.2
- ON/OFF Switch
- NO














