Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

This 8-pin Boyu wafer male connector mounts through a PCB at a right angle, so a mating harness can run parallel to the board. It is rated 1A at 50V DC and suits compact low-power signal wiring.

Key Highlights

  • 8-pin wafer male connector with 1.5 mm pitch for compact layouts
  • Right-angle through-hole body keeps the harness parallel to the PCB
  • Rated 1A and 50V DC for low-power signal and control lines
  • Works across -40 °C to +85 °C for varied environments
  • Contact resistance specified at 20M max
  • Accepts fine wire sizes for small-gauge hookup cable

Ideal For

  • Electronics hobbyists building compact prototype boards
  • Repair technicians replacing a damaged right-angle connector
  • Developers wiring low-current signal and control lines
  • Makers who need a pluggable harness inside a slim enclosure
  • Small-batch assembly work using 1.5 mm pitch connectors

Buying Tip

Check that you have the matching female housing and crimp contacts before ordering, because this listing is for the male wafer connector only.

Elecvora expert review

Our verdict

A neat, purpose-built connector for compact boards that need eight low-power lines with a side-exit harness. It does one job well and makes no claims beyond its modest electrical ratings.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Right-angle layout saves vertical space
  • Eight pins in a small 1.5 mm pitch footprint
  • Clear 1A and 50V DC ratings for low-power planning
  • Wide -40 °C to +85 °C operating range

Cons

  • Mating connector is not included
  • Limited to low-current circuits
  • Fine pin spacing demands careful soldering

Best for

Compact PCB builds and repairs needing a pluggable eight-way side-exit connection

Not ideal for

Higher-current power distribution or applications without a matching female housing

Specifications

ManufacturerBoyu
Rated Current (A)1
Rated Voltage (VDC)50
Operating Temperature (°C)-40 °C to +85 °C
Contact Resistance (ohm)20M max
Configuration8 pin Wafer Male Connector Through Hole Right Angle
Mounting TypeThrough Hole Straight
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

What's in the box

  • 1 x Boyu 1.5AW 1.5mm 8-pin wafer male connector, through-hole right angle

Frequently Asked Questions

Is the mating connector included?
No. The listing covers one male wafer connector only, so you will need the matching female housing and contacts separately.
What current and voltage can it handle?
It is rated for 1A and 50V DC, which places it in low-power signal and control applications rather than high-draw circuits.
What wire sizes does it accept?
The connector is intended for fine wire in the small-gauge range. Confirm your wire gauge against the mating contact specification before crimping.
How is it mounted on a board?
It uses through-hole pins that are soldered to the PCB, with the right-angle body letting the harness exit parallel to the board.
What temperature range does it support?
The connector is rated from -40 °C to +85 °C, so it can be used in cold storage or warm enclosure conditions within that window.
How should I care for it?
Keep the contacts clean and dry, avoid pulling on the cable when unplugging, and do not exceed the rated current or voltage.

Overview

The Boyu 1.5AW is an 8-pin wafer male connector built for through-hole PCB mounting. Its 1.5 mm pitch and right-angle body make it a compact option when a board needs a pluggable connection but has little vertical clearance to spare. Instead of a header standing upright, the mating harness approaches the board from the side, which helps in slim enclosures and stacked assemblies.

This is a connector for low-power work: signal lines, control leads, sensor wiring and small module links. It is supplied as a single connector, so it is a sensible choice for repairs, one-off builds and prototypes where you need a specific part rather than a bulk reel.

Key Features

  • Eight contacts in a 1.5 mm pitch wafer format
  • Right-angle male connector with through-hole pins
  • Rated current of 1A and rated voltage of 50V DC
  • Operating temperature range of -40 °C to +85 °C
  • Contact resistance specified at 20M max
  • Compact body suited to dense board layouts

Specifications Explained

Current and voltage

The 1A current rating tells you this part is intended for low-power circuits, not for motors or high-draw loads. The 50V DC rating is comfortably above the low voltages used in most small electronics, so it fits typical signal and control applications.

Contact resistance

A contact resistance figure of 20M max gives buyers a reference point for the connector's electrical behaviour. In practice, this part belongs in circuits where small contact losses are acceptable, such as logic-level signals and low-current supplies.

Temperature range

Operation from -40 °C to +85 °C means the connector is not limited to a climate-controlled bench. It can be used in equipment that sees cold storage or warm enclosures, provided the rest of the assembly is rated for the same conditions.

Mounting style

The through-hole, right-angle configuration is soldered into the board. The right-angle exit is the practical detail many builders care about: it changes how the cable leaves the PCB and can simplify routing inside a case.

Compatibility and Requirements

This connector is designed for through-hole soldering and accepts fine wire sizes in the small-gauge range. It requires a matching mating connector, which is not included, and it should only be used within its 1A and 50V DC ratings. Confirm your wire gauge and mating half before ordering, since the connector alone will not complete a connection.

Typical Uses

Common applications include internal signal wiring in small electronic devices, control leads in compact modules, sensor connections and prototype boards that need a removable harness. It is also useful for repair work where an original right-angle connector has been damaged and needs replacing with a like-for-like part.

What's in the Box

One Boyu 1.5AW 1.5mm 8-pin wafer male connector, through-hole right angle. No mating connector, wire or hardware is included.

Quick specs

Manufacturer
Boyu
Rated Current (A)
1
Rated Voltage (VDC)
50
Operating Temperature (°C)
-40 °C to +85 °C
Contact Resistance (ohm)
20M max
Configuration
8 pin Wafer Male Connector Through Hole Right Angle
See all specifications