Skip to main content

Worldwide Shipping · Secure Payments

At a glance

This battery charger module is a good fit for makers, students and electronics hobbyists. Main specs: output voltage 12; output current (a) 3; power supply voltage (v) 15-28VDC(Recommended 16-25VDC). Check that your power source supplies 12 before connecting it.

Key Highlights

  • Output Voltage: 12
  • Output Current (A): 3
  • Power Supply Voltage (V): 15-28VDC(Recommended 16-25VDC)

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Output Voltage12
Output Current (A)3
Power Supply Voltage (V)15-28VDC(Recommended 16-25VDC)
Additional Specs.Over Charge Voltage: 14.8V Float Charge Voltage: 13.55V
Max Current Continuous (A)3A
Quiescent Current1.8mA
Switching frequency300kHz
Operating Temperature (°C)-40°C to +85°C
Size (mm)66 x 20x 12mm
Weight (g)9 gm
Shipping Weight0.01 kg
Shipping Dimensions9 × 8 × 1 cm

Overview

The HOT DD30CRTA Car, Lead Acid Battery, Charger 12V Charging, Device 3A Current 1-, 10000AH UPS Solar, Power Module, (With Terminal) is listed in our battery charger module range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Output Voltage: 12 (match this to your power supply; too high a voltage can damage the part)
  • Output Current (A): 3 (your supply must deliver at least this much current)
  • Power Supply Voltage (V): 15-28VDC(Recommended 16-25VDC) (match this to your power supply; too high a voltage can damage the part)
  • Additional Specs.: Over Charge Voltage: 14.8V Float Charge Voltage: 13.55V (match this to your power supply; too high a voltage can damage the part)
  • Max Current Continuous (A): 3A (your supply must deliver at least this much current)
  • Quiescent Current: 1.8mA (your supply must deliver at least this much current)
  • Switching frequency: 300kHz (make sure the rest of your system works at this frequency)
  • Operating Temperature (°C): -40°C to +85°C

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

This is HOT DD30CRTA Lead Acid Battery Charger 12V Charging Device 3A.
The DD30CRTA is a PWM switch-mode battery charger controller for a 12V lead-acid battery in a small package using a few external components. The DD30CRTA is specially designed for charging 12V lead-acid battery with trickle charge, constant current charge, over-charge and float charge mode. In over-charge and float charge mode, the regulation voltage is internally set.
The constant charge current is programmable with a single sense resistor.
 Deeply discharged batteries are automatically trickle charged at 17.5% of the programmed constant charge current until the cell voltage exceeds 75% of the regulation voltage in over-charge mode. The over-charge is terminated once the charging current drops to 38% of the constant charge current, then DD30CRTA will enter float charge mode. A new charge cycle automatically restarts if the battery voltage falls below 83.95% of the over-charge voltage in float-charge mode. DD30CRTA will automatically enter sleep mode when the input voltage is lower than the battery voltage.
Other features include under-voltage lockout and indication, etc.
1: The Regulation Voltage in Over Voltage Mode and Float Charge Mode
The regulation voltage VOC at BAT pin in overcharge mode is set at 14.8V(Typical) with ±1.5% accuracy.
In float charge mode, the regulation voltage VFLOAT at BAT pin is 91.57% of that in overcharge mode, which is 13.55V(Typical).
Trickle Charge Mode At the beginning of a charge cycle, if the battery voltage is below 75%×VOC, the charger goes into trickle
charge mode with the charge current set at about 17.5% of the constant current.
2: End-of-Over Charge Current
When the battery voltage approaches the over-charge voltage, the charger goes into the overcharge mode. In
overcharge mode, the charge current start to decrease and when the charge current drops to 38% of constant
charge current, the charger goes into float-charge mode.
3: Float Charge Mode
After the overvoltage charge is terminated, the charger goes into float charge mode. In float charge mode, the
battery voltage is regulated to 91.57%×VOC, namely 13.55V(Typical). Float charge mode can compensate for
the loss of battery power due to self-discharge or external loading.
4: Automatic Battery Recharge
In float mode, if both the battery and the input power supply (wall adapter) are present, a new charge cycle will
begin if the battery voltage drops below 83.95%×VOC due to self-discharge or external loading.
A new charge cycle can also be started manually by plugging off the input supply and reapplying it.

Application:

  1. Car battery charging
  2. Solar battery charging
  3. Loudspeaker
  4. Lead-Acid Battery Charger
  5. Electric Bicycle Charger
  6. UPS
  7. Portable Industrial and Medical Equipment
  8. Standalone Battery Chargers

Features:

  1. Fixed Over-Charge Voltage
  2. Overcurrent protection
  3. Automatic Conditioning of Deeply Discharged Batteries
  4. Automatic Recharge
  5. Charger Indication
  6. Battery Overvoltage Protection
  7. Suitable for 1-10000AH 12V Lead-Acid Battery charger

Package Includes:

1 x HOT DD30CRTA Lead Acid Battery Charger 12V Charging Device 3A

Quick specs

Output Voltage
12
Output Current (A)
3
Power Supply Voltage (V)
15-28VDC(Recommended 16-25VDC)
Additional Specs.
Over Charge Voltage: 14.8V Float Charge Voltage: 13.55V
Max Current Continuous (A)
3A
Quiescent Current
1.8mA
See all specifications