
1 / 6 · Click to enlarge
AI Summary
A sealed DS18B20 digital temperature probe on a 1 m cable, rated from -55°C to +125°C with ±0.5°C accuracy. It needs only one digital pin thanks to the 1-Wire interface, and multiple probes can share that pin.
Key Highlights
- DS18B20 1-Wire digital sensor needs just one data pin
- Waterproof 6 mm stainless steel probe with sealed cable entry
- Wide -55°C to +125°C measuring range at ±0.5°C accuracy
- Selectable 9 to 12-bit resolution for precision or speed
- Runs on 3 to 5.5 VDC for common microcontroller boards
- One-metre cable keeps the sensor away from heat sources
Ideal For
- Makers building multi-point temperature logging systems
- Home brewers and aquarium hobbyists measuring liquid temperature
- Gardeners and growers monitoring soil or greenhouse conditions
- Weather station builders needing an outdoor probe
- Students learning 1-Wire sensor interfacing
Buying Tip
Remember to fit a 4.7 kΩ pull-up resistor between the DATA and VCC lines, since it is not supplied with the probe.
Elecvora expert review
Our verdict
A dependable, low-cost probe for anyone who needs digital temperature readings in a wet or distant location. The 1-Wire design keeps wiring simple and makes multi-sensor setups practical.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Waterproof stainless housing suits liquids and outdoor use
- Single-pin 1-Wire interface simplifies wiring
- Wide -55°C to +125°C range with ±0.5°C accuracy
- Unique 64-bit ID allows several probes on one bus
Cons
- 4.7 kΩ pull-up resistor is not included
- 750 ms query time limits very fast sampling
- Unbranded unit, so build quality may vary between batches
Best for
Liquid, soil and outdoor temperature monitoring with microcontrollers
Not ideal for
Applications needing sub-0.5°C precision or rapid sampling
Specifications
| Item Type | Probe |
|---|---|
| Rated Voltage (VDC) | 3 to 5.5 |
| Probe Diameter | 6mm |
| Probe Length (mm) | 50mm |
| Resolution | 9 ~ 12 bit |
| Query time | 750 msec |
| Cable Length | 1 |
| Model No. / Name | DS18B20 |
| Accuracy | ±0.5°C |
| Operating Voltage (VDC) | 3 ~ 5.5 |
| Measuring Temperature (°C) | -55 ~ +125 °C |
| Operating Temperature (°C) | -55 to 125 |
| Shipping Weight | 0.08 kg |
| Shipping Dimensions | 7 × 5 × 3 cm |
What's in the box
- 1 x Waterproof DS18B20 digital thermal probe with 1 m cable
Frequently Asked Questions
Do I need a resistor to use this probe?
Can I connect more than one probe to the same pin?
What voltage does it need?
Is the probe safe to immerse in liquid?
What is included in the package?
How accurate is the reading?
Overview
The DS18B20 Waterproof Temperature Probe pairs a DS18B20 digital sensor with a sealed 6 mm stainless steel tube and a one-metre cable. Instead of delivering a small analogue voltage that drifts with cable length, the probe converts temperature internally and sends the reading as digital data over the 1-Wire bus. That makes it a sensible option when the measurement point is some distance from the board or sits in a damp environment.
Key Features
- 1-Wire interface: a single digital pin carries communication, so wiring stays simple.
- Unique 64-bit ID: every probe is individually identifiable, allowing several sensors on one data line.
- Waterproof stainless housing: the 6 mm tube and sealed cable entry protect the sensor from moisture.
- Digital output: no signal degradation over the length of the cable.
- Wide temperature range: measures from -55°C to +125°C.
Specifications Explained
Accuracy and resolution
The probe is specified at ±0.5°C, which is adequate for environmental monitoring, liquid temperature checks and general project logging. Resolution is configurable between 9 and 12 bits, letting you trade finer steps for faster readings. Query time is stated as 750 ms, so plan your sampling interval around that figure rather than polling continuously.
Voltage and wiring
Operating voltage spans 3 to 5.5 VDC, covering the usual 3.3 V and 5 V logic levels. The three conductors are colour coded: red for VCC, yellow or white for DATA and black for GND. Each pin is protected with heat-shrink tubing to reduce the risk of a short circuit.
Physical size
The stainless tube is 6 mm in diameter and 50 mm long, with a one-metre cable attached. That length is useful for reaching into a tank, soil bed or enclosure while keeping the electronics outside.
Compatibility and Requirements
The probe works with any microcontroller that supports a single digital pin and the 1-Wire protocol. A 4.7 kΩ pull-up resistor between the DATA line and VCC is required, and it is not included. Ensure your supply stays within the 3 to 5.5 VDC range before connecting the probe.
Typical Uses
- Monitoring water, beer or other liquids in a container
- Soil and greenhouse temperature logging
- Outdoor weather stations and enclosure sensing
- Multi-point temperature arrays using one data pin
- General electronics and automation projects
What's in the Box
One waterproof DS18B20 digital thermal probe with a one-metre cable.

Quick specs
- Item Type
- Probe
- Rated Voltage (VDC)
- 3 to 5.5
- Probe Diameter
- 6mm
- Probe Length (mm)
- 50mm
- Resolution
- 9 ~ 12 bit
- Query time
- 750 msec
















