
1 / 2 · Click to enlarge
At a glance
This fingerprint sensors is a good fit for makers, students and electronics hobbyists. Main specs: item type Control Board; model no. / name KL202; processor STM8. Check that your power source supplies 10 to 24 before connecting it.
Key Highlights
- Item Type: Control Board
- Model No. / Name: KL202
- Processor: STM8
Ideal For
- Arduino, ESP32 and Raspberry Pi projects
- School and college lab work
- Prototypes and test rigs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Item Type | Control Board |
|---|---|
| Operating Voltage (V) | 10 to 24 |
| Model No. / Name | KL202 |
| Processor | STM8 |
| Output Type | Relay (Max current: 10A) |
| Fingerprint Capacity | 120 |
| Scanning Speed | < 0.2 second |
| Verification Speed | < 0.3 second |
| Matching Method | 1:1; 1:N |
| False Rejection Rate | ≤1% |
| False Acceptance Rate | ≤0.001% |
| Operating Temperature (°C) | -20 to 60 |
| Operating humidity | 10 to 85% |
| Standby Current (µA) | 15uA |
| Shipping Weight | 0.08 kg |
| Shipping Dimensions | 5 × 4 × 2 cm |
Overview
The Grow KL202 +R503 DC12V Low Power Consumption Ring Fingerprint Access Control Board is listed in our fingerprint sensors range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Item Type: Control Board
- Operating Voltage (V): 10 to 24 (match this to your power supply; too high a voltage can damage the part)
- Model No. / Name: KL202
- Processor: STM8 (look up this chip to confirm it runs the firmware or libraries you plan to use)
- Output Type: Relay (Max current: 10A) (your supply must deliver at least this much current)
- Fingerprint Capacity: 120
- Scanning Speed: < 0.2 second
- Verification Speed: < 0.3 second
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
This Grow KL202+R503 DC12V Low Power Consumption Ring Fingerprint Access Control Board is an all-in-one control board with the onboard STM8 microcontroller. This module can act as a standalone system for the fingerprint access control system. The board comes with an onboard relay which is activated by the microcontroller when the fingerprint is detected. The activation time of the relay can be controlled via a multiturn potentiometer, which can be adjusted through 0.5 sec -13 sec.
How To Use:
- After providing power to the module, the module will be in its initial factory mode where any fingerprint can activate the relay.
- To register the fingerprint long press the SET button for 3-4 sec, when the BLUE LED starts blinking it indicates that the module is ready to register the fingerprint.
- Now place the finger which you want to register on the scanner and after the 5 beeps remove the finger. If you want to add other fingerprints then you can add or wait for some time till the LED stops blinking.
- After the LED stops blinking you can use the registered fingerprint to activate the relay. When a registered fingerprint is read by the sensor the BLUE led will glow around the sensor and a RED/ORANGE led will glow if an unregistered fingerprint is detected.
- The SET time of the relay can be adjusted by the multiturn potentiometer.
Features:
- Low Power Consumption.
- 120 Fingerprint Capacity.
- Low Power Consumption.
Package Includes:
1 x Grow KL202+R503 DC12V Low Power Consumption Ring Fingerprint Access Control BoardQuick specs
- Item Type
- Control Board
- Operating Voltage (V)
- 10 to 24
- Model No. / Name
- KL202
- Processor
- STM8
- Output Type
- Relay (Max current: 10A)
- Fingerprint Capacity
- 120













