Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The Grow KR501 is a compact fingerprint control board that stores up to 20 prints and runs from 3.7-10V. It outputs a 3.3V signal for one second after a match, making it easy to trigger a lock, relay or microcontroller input.

Key Highlights

  • Stores up to 20 fingerprints on board
  • Wide 3.7-10V DC input suits small battery packs
  • Ultra-low 2.5-7uA standby current draw
  • One-second 3.3V high-level output after a match
  • Compact 36mm diameter board for tight builds
  • On-board registration and deletion with light and sound feedback

Ideal For

  • Makers building fingerprint-triggered locks and latches
  • Home and workshop access control projects
  • Battery-powered enclosures needing low idle drain
  • DIY electronics builds that trigger a relay or MCU input
  • Small cabinets, drawers and storage boxes

Buying Tip

Register at least two fingerprints during initial setup, because the board stays in its initialisation state until more than two correct prints have been enrolled.

Elecvora expert review

Our verdict

The KR501 is a tidy, low-power fingerprint module that keeps enrolment and matching on board, which makes it a practical choice for small access projects. Its one-second 3.3V output and wide input range make integration straightforward for anyone comfortable wiring a trigger signal.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Stores up to 20 prints without a host controller
  • Very low 2.5-7uA standby current
  • Wide 3.7-10V input range
  • Simple on-board registration and deletion
  • Compact 36mm diameter board

Cons

  • Output is a fixed one-second pulse, not a latched state
  • No enclosure or mounting hardware included
  • Requires a separate DC supply and downstream driver

Best for

Makers and hobbyists building small fingerprint-triggered access projects

Not ideal for

Large multi-user access systems needing many stored prints

Specifications

Item TypeControl Board
Model No. / NameFingerprint Control Board
Fingerprint Capacitycan store upto 20
Power output(V)3.7 - 10
Stand-by mode current2.5 - 7 uA
Max. Operating Current (A)40 - 250mA
Shipping Weight0.1 kg
Shipping Dimensions5 × 5 × 4 cm

What's in the box

  • 1 x KR501 Fingerprint Control Board

Frequently Asked Questions

How many fingerprints can the KR501 store?
The board can store up to 20 fingerprints. For the first setup, enrol more than two correct prints so the system leaves its initialisation state.
What voltage does the board need?
It accepts a DC input between 3.7 and 10V. Choose a supply within that range and account for the 40-250mA operating current during a read.
What does the output do after a print is recognised?
The OUT1 pin outputs a high-level signal at 3.3V and up to 500mA for one second. Use that pulse to trigger a relay, lock driver or microcontroller input.
How do I delete all stored fingerprints?
Long press a registered finger until the red indicator lights, or in standby ground the INIT_KEY pin until the red light and tone appear, then disconnect. Both actions return the board to the initialisation state.
What is included with the board?
The package contains one KR501 Fingerprint Control Board. A power supply, wiring and downstream driver are not included.
How much current does it draw when idle?
Standby current is between 2.5 and 7uA, which is very low and suits battery-powered projects where idle drain matters.

Overview

The Grow KR501 is a standalone fingerprint control board for adding biometric access control to your own hardware. It handles enrolment, matching and output signalling on a single compact board, so you do not need a separate host controller to decide whether a print is valid. Once a stored fingerprint is recognised, the OUT1 pin produces a high-level signal at 3.3V for one second, which is long enough to latch a relay, release a solenoid or wake a microcontroller.

The board is built around low-power operation. A standby current of only 2.5 to 7uA means it can sit idle for long periods without flattening a small battery, while the operating current stays between 40 and 250mA during active reads. The 3.7-10V input range gives you flexibility in how you power it, from a single lithium cell up to a higher regulated rail.

Key Features

  • 20-print capacity: enough for a household, a small workshop or a personal project with several authorised users.
  • Wide input range: accepts DC 3.7-10V, so it suits a range of battery and supply options.
  • Low idle drain: 2.5-7uA standby current keeps quiescent consumption minimal.
  • Clean output signal: OUT1 provides 3.3V at up to 500mA for one second after a successful match.
  • Compact footprint: a 36mm diameter board that fits into small enclosures and panels.
  • Simple local control: register and delete prints using the sensor area and the INIT_KEY pin, with LED and audible confirmation.

Specifications Explained

Fingerprint capacity

The board can store up to 20 fingerprints. That is well suited to a single door, a cabinet, a drawer or a small group of users rather than a large multi-user installation.

Power input and current

The 3.7-10V input range covers common small lithium cells and regulated supplies. Standby current of 2.5-7uA is very low, so the board is not a significant drain when idle. During a read, expect 40-250mA, which is worth accounting for when sizing a supply or battery.

Output behaviour

After a print passes, OUT1 outputs 3.3V at up to 500mA for one second. That pulse is the trigger for whatever you connect downstream. Because it is a fixed one-second signal, your relay or driver should respond to a momentary high level.

Size

At 36mm in diameter, the board is small enough for panel mounting in compact projects. Shipping weight is listed at 0.1kg.

Compatibility and Requirements

The KR501 works as a self-contained module: it reads prints and provides the output signal itself. You will need a DC supply within the 3.7-10V range and a downstream device that accepts a 3.3V, one-second high-level trigger. The INIT_KEY pin can be grounded to clear all stored prints and return the board to its initialisation state.

Typical Uses

  • Fingerprint-triggered locks on cabinets, drawers and storage boxes
  • Access control for a single door in a home or small workshop
  • Triggering a relay or microcontroller input in a DIY electronics build
  • Battery-powered projects where low standby current matters

What's in the Box

  • 1 x KR501 Fingerprint Control Board

Quick specs

Item Type
Control Board
Model No. / Name
Fingerprint Control Board
Fingerprint Capacity
can store upto 20
Power output(V)
3.7 - 10
Stand-by mode current
2.5 - 7 uA
Max. Operating Current (A)
40 - 250mA
See all specifications