
1 / 5 · Click to enlarge
AI Summary
A bench-top RF and communication trainer that produces 0.1 to 3 MHz baseband waveforms and an 870 to 920 MHz carrier for AM and FM modulation experiments. Five test points and programmable switches let instructors create fault conditions for hands-on troubleshooting practice.
Key Highlights
- Baseband sine, square and triangle waveforms from 0.1 MHz to 3 MHz
- RF carrier output tunable across the 870 MHz to 920 MHz range
- AM and FM modulation for practical analogue communication lessons
- Five test points and five programmable switches for fault simulation
- USB device interface enables remote control during guided sessions
- Compact 165 x 155 x 90 mm housing with 1.5 kg shipping weight
Ideal For
- University RF and communication laboratory instructors
- Vocational school telecommunication trainers
- Military and corporate technical training centres
- Students learning AM and FM modulation fundamentals
- Electronics teaching staff building troubleshooting exercises
Buying Tip
Confirm whether your course also needs the companion GSP-730 spectrum analyser, since it is not part of this package.
Elecvora expert review
Our verdict
The GRF 1300 A is a focused teaching instrument rather than a general-purpose signal generator, and that focus is its strength. It packages baseband generation, UHF carrier output and built-in fault simulation into one small bench unit suited to structured laboratory programmes.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Purpose-built for AM and FM modulation teaching
- Three baseband waveform shapes across a wide range
- Fault simulation supports real troubleshooting practice
- USB control helps instructors manage class sessions
- Compact footprint with low shipping weight
Cons
- Companion spectrum analyser is not included
- No probes, cables or software listed in the package
- Limited to the specified 870 to 920 MHz carrier band
Best for
University and vocational RF communication laboratory courses
Not ideal for
Engineers needing a general-purpose broadband signal generator
Specifications
| Interface | USB Device |
|---|---|
| Dimensions (L x W x H) mm | 165(W) x 155 (H) x 90 (D) |
| Shipping Weight | 1.5 kg |
| Shipping Dimensions | 20 × 15 × 10 cm |
What's in the box
- 1 x GW Instek GRF 1300 A RF and Communication Trainer System
Frequently Asked Questions
What waveforms can the GRF 1300 A generate?
What is the RF output frequency range?
Does it support both AM and FM?
How is fault simulation handled?
Can it be controlled from a computer?
Is the spectrum analyser included?
Overview
The GW Instek GRF 1300 A is a dedicated teaching instrument for RF and communication laboratories. It produces the two ingredients every analogue radio experiment needs: a baseband information signal and a high-frequency carrier. Students can observe how a low-frequency waveform is impressed onto an RF carrier and how the resulting modulated signal behaves when measured and demodulated.
Because the unit is purpose-built for instruction, it also includes facilities for deliberate fault injection. That turns a demonstration into an exercise in diagnosis, which is where most practical learning happens.
Key Features
- Sine, square and triangle baseband outputs spanning 0.1 MHz to 3 MHz
- RF output covering 870 MHz to 920 MHz
- AM and FM modulation topics supported by the built-in signal path
- Five programmable on/off switches for configuring experiments
- Five test points used to simulate eight failure conditions for troubleshooting study
- USB device interface for remote control
Specifications Explained
Baseband waveform range
The 0.1 MHz to 3 MHz span covers the audio and low-frequency signalling region typically used to illustrate modulation. Having three waveform shapes available lets instructors compare how a sine, square or triangle modulating signal changes the modulated output.
RF carrier range
Operating between 870 MHz and 920 MHz places the carrier in the UHF region, which is representative of many short-range communication links. This makes the measurements feel closer to real hardware than a purely audio-frequency simulation.
Test points and switches
Five test points give students defined measurement locations, while the five programmable switches are used to introduce the eight simulated failure conditions. The combination supports structured fault-finding practice instead of passive observation.
USB interface
The USB device port allows the trainer to be controlled remotely, which is useful when an instructor wants to coordinate settings across a class or run scripted laboratory sequences.
Physical size
At 165 mm wide, 155 mm high and 90 mm deep, the unit occupies little bench space. Shipping weight is 1.5 kg and shipping dimensions are 20 x 15 x 10 cm.
Compatibility and Requirements
The GRF 1300 A provides a USB device interface for remote control. No host software, operating system version or accessory kit is specified in the available product data, so buyers should confirm their laboratory setup separately. The unit is described as part of a training system alongside the GSP-730 spectrum analyser, which is not included with this item.
Typical Uses
- University and college RF communication laboratory modules
- Vocational school telecommunication practical classes
- Military and private company training centre coursework
- Demonstrating AM and FM modulation concepts on the bench
- Troubleshooting exercises using simulated failure conditions
What's in the Box
The package contains one GW Instek GRF 1300 A RF and Communication Trainer System. No additional cables, probes or software are listed in the supplied product data.
Quick specs
- Interface
- USB Device
- Dimensions (L x W x H) mm
- 165(W) x 155 (H) x 90 (D)
- Shipping Weight
- 1.5 kg
- Shipping Dimensions
- 20 × 15 × 10 cm














