Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact HX711-based sensor module that brings high-precision weight and pressure readings to Arduino, Raspberry Pi, ESP32, STM32 and PLC projects. It runs on a 3.3 to 5 V interface with under 20 mA current draw and installs tool-free.

Key Highlights

  • Built around the HX711 chip for precise load sensing
  • Works with Arduino, Raspberry Pi, STM32, ESP32 and PLC systems
  • 3.3 to 5 V interface voltage for flexible project power
  • Low working current under 20 mA
  • Compact 50 x 32 mm board weighing just 11 g
  • Tool-free installation and easy replacement

Ideal For

  • Makers building load cell weighing projects with Arduino
  • Students learning sensor interfacing on Raspberry Pi or ESP32
  • Automation hobbyists integrating sensors into PLC setups
  • Engineers prototyping pressure and stress test rigs
  • Workshops that need a compact, replaceable sensor board

Buying Tip

Confirm your controller's logic level falls within the 3.3 to 5 V interface range before wiring, and check that your load cell wiring matches the board's connections.

Elecvora expert review

Our verdict

A tidy, low-cost HX711 board that does one job well: giving a controller a clean path to a load cell. It is compact, easy to swap and covers the common 3.3 to 5 V platforms, though it is a bare module rather than a finished scale.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Small 50 x 32 mm footprint and only 11 g
  • Works across Arduino, Raspberry Pi, STM32, ESP32 and PLC systems
  • Low working current under 20 mA
  • Tool-free installation and easy replacement

Cons

  • No load cell, wiring or controller included
  • Limited published detail beyond the listed specifications
  • Requires your own calibration and code

Best for

Makers and engineers adding weight or pressure sensing to an existing controller project

Not ideal for

Buyers wanting a ready-to-use digital scale out of the box

Specifications

Item TypeSensor Module
Model No. / NameHX711
Based OnHX711 Chip
CompatibilityArduino, Raspberry Pi, STM32, ESP32, PLC Systems
Interface voltage3.3 to 5
Operating Voltage (VDC)05
Working Current (mA)<20
Length (mm)50
Width (mm)32
Weight (g)11
Dimensions (L x W x H) mm170 x 130 x 130
InstallationTool-Free, Easy Replacement
Shipping Weight0.012 kg
Shipping Dimensions10 × 6 × 2 cm

What's in the box

  • 1 x HX711 Pressure Sensor Test Board

Frequently Asked Questions

What controller can I use with this board?
The module is listed for Arduino, Raspberry Pi, STM32, ESP32 and PLC systems. Any of these can serve as the host as long as your supply sits within the stated interface voltage range.
What voltage does the board need?
The interface voltage is listed as 3.3 to 5 V, and working current is under 20 mA. Check your own supply against these figures before connecting.
Is a load cell included?
No. The package contains one HX711 Pressure Sensor Test Board only, so you will need to supply your own load cell or sensing element, wiring and controller.
How big is the module?
The board measures approximately 50 mm long and 32 mm wide and weighs about 11 g, which makes it easy to fit into small enclosures.
Can I replace it easily?
Yes. The board is designed for tool-free installation and easy replacement, which helps when servicing a test rig or swapping a module in the field.
Do I need to calibrate it?
Yes. As with any load cell front end, you will need to take readings at known loads and adjust your code so the output matches your reference values.

Overview

The HX711 Pressure Sensor Test Board is a compact module that gives your project a dedicated front end for weight and pressure sensing. It is built on the HX711 chip, a part widely used when a load cell signal needs to be read accurately by a microcontroller or control system. The board measures about 50 mm by 32 mm and weighs only 11 g, so it slots into small enclosures, prototype plates and test fixtures without crowding the layout.

This is a component for builders rather than a plug-and-play instrument. If you already work with Arduino, Raspberry Pi, STM32, ESP32 or PLC systems, the board is designed to fit into that kind of environment.

Key Features

  • HX711 chip: the core of the module, intended for high-precision sensor signal handling.
  • Broad platform support: listed for Arduino, Raspberry Pi, STM32, ESP32 and PLC systems.
  • Flexible interface voltage: operates from a 3.3 to 5 V interface supply.
  • Low current draw: working current stays below 20 mA.
  • Compact footprint: 50 mm length and 32 mm width keep wiring runs short.
  • Simple servicing: tool-free installation and easy replacement when a board needs swapping.

Specifications Explained

Interface voltage of 3.3 to 5 V means the board can sit alongside both 3.3 V logic boards and 5 V controllers, which covers most hobby and industrial development platforms. Working current under 20 mA is modest, so the module adds little load to a small supply. The 50 x 32 mm board size and 11 g weight matter when you are fitting a sensor into a handheld tester or a dense control cabinet. The listed operating voltage field should be checked against your own supply before wiring, and the tool-free installation design keeps field replacement straightforward.

Compatibility and Requirements

The module is listed as compatible with Arduino, Raspberry Pi, STM32, ESP32 and PLC systems, with a 3.3 to 5 V interface voltage. You will need a host controller from that list, a suitable supply within the stated range, and a load cell or pressure sensing element to connect to the board. Plan your wiring and mounting before installation, and confirm the supply voltage of your system matches the module's stated interface range.

Typical Uses

  • Load cell based weighing projects on Arduino or Raspberry Pi
  • Mechanical stress and pressure testing in a workshop
  • Small automation builds using PLC or ESP32 control
  • Student and maker projects that need a precise sensor front end
  • Prototype test rigs where a compact board is an advantage

What's in the Box

The package includes one HX711 Pressure Sensor Test Board. Load cells, jumper wires, controllers and power supplies are not included.

Quick specs

Item Type
Sensor Module
Model No. / Name
HX711
Based On
HX711 Chip
Compatibility
Arduino, Raspberry Pi, STM32, ESP32, PLC Systems
Interface voltage
3.3 to 5
Operating Voltage (VDC)
05
See all specifications

Explore more