
1 / 3 · Click to enlarge
AI Summary
A professional-grade flight controller kit for industrial multi-rotor drones, supporting 3S-12S LiPo power and S.Bus receivers. It covers four-, six- and eight-rotor layouts with a separate PMU and optional UPS module for stable, well-organized power.
Key Highlights
- Supports I4, X4, Y6, V6, V8, I8, X8 and IX8 multi-rotor layouts
- 3S to 12S lithium polymer battery input for flexible builds
- S.Bus receiver compatibility for simple single-wire connection
- Separate PMU plus optional PMU 2 UPS with 3A at 5V output
- ±1.5m horizontal and ±0.5m vertical positioning accuracy
- Configuration software runs on Windows 7, 8 and 10, 32 or 64 bit
Ideal For
- Agricultural spray drone builders working with 6S-12S packs
- Mapping and survey pilots flying large multi-rotor platforms
- Aerial photography crews lifting heavier camera payloads
- Engineers building redundant eight-rotor airframes
- Hobbyists moving up to industrial-grade flight control hardware
Buying Tip
Check that your receiver outputs S.Bus and that your main pack is at least 11.1V before wiring the PMU, since the controller itself only accepts 4.8-5.3V.
Elecvora expert review
Our verdict
The Jiyi K++ V2 is a capable industrial-grade controller for builders who need high-voltage input and flexible multi-rotor support in one kit. Its separate PMU and optional UPS make power planning straightforward on larger airframes.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Handles 3S-12S LiPo input without extra regulators
- Covers four-, six- and eight-rotor layouts in one unit
- Separate PMU and optional UPS simplify 5V power distribution
- Low under-5W controller consumption
Cons
- Configuration requires a Windows PC
- Only S.Bus receivers are specified
- No package contents beyond the kit are listed
Best for
Industrial multi-rotor builds such as spray, mapping and camera-lift drones
Not ideal for
Beginners wanting a plug-and-play, app-configured controller
Specifications
| Item Type | Kit |
|---|---|
| Supported | I4 , X4 four rotor ,iy6 , y6 , 16 , v6 six rotor v8 i8 x8 ix8 8 rotor |
| Battery Type | 3s -12s lithium polymer battery |
| Receiver Type | Sbus receiver |
| OS Supports | windows 7,8,10( 32 bit and 64 bit) |
| Accuracy | Horizontal direction : ±1.5m vertical direction ±0.5m |
| Step Angle | 30 degree Tilt angle |
| Maximum Yaw Speed | 150 Degree |
| Maximum Vertical Speed | 6m/s |
| Maximum Wind Resistance | wind 4 gust 5 |
| Power Consumption (W) | <5W |
| Voltage Range of FC | 4.8V - 5.3V |
| PMU | 11.1V - |
| PMU 2 (UPS) | 11.1 - 50v (3s - 12s lipo recommended) maximum output current 3A at 5V |
| GPS | 5v |
| LED Voltage | 5V |
| Voltage (V) | 3s - 12s |
| Shipping Weight | 0.38 kg |
| Shipping Dimensions | 18 × 13 × 5 cm |
What's in the box
- 1 x Jiyi K++ V2 Flight Controller Kit
Frequently Asked Questions
What battery voltage does the Jiyi K++ V2 support?
Which receivers work with this flight controller?
What computer do I need to configure it?
What frame types are supported?
How much power does the controller draw?
What is included in the package?
Overview
The Jiyi K++ V2 Flight Controller Kit is a professional-grade flight control package aimed at industrial multi-rotor aircraft. It is intended for builders working on plant protection sprayers, mapping platforms and aerial photography rigs who need a controller that handles large battery packs and a wide range of frame layouts. The kit pairs the flight controller with a separate power management unit and supports an optional second PMU (UPS) for builds that need a backed-up 5V rail.
Key Features
- Broad frame support: works with I4, X4 four-rotor, IY6, Y6, V6 six-rotor, I6, V8, I8, X8 and IX8 eight-rotor configurations.
- Wide voltage range: accepts 3S to 12S lithium polymer batteries, so the same controller suits small and large airframes.
- Simple receiver wiring: designed for S.Bus receivers, keeping the connection between radio and controller to a single signal line.
- Dual power modules: the main PMU takes 11.1V and above, while PMU 2 (UPS) accepts 11.1-50V and provides up to 3A at 5V.
- Stable positioning: rated to ±1.5m horizontally and ±0.5m vertically, with a 6m/s maximum vertical speed and 150 degrees per second maximum yaw rate.
- Low power draw: the controller consumes under 5W, leaving more capacity for payload and propulsion.
Specifications Explained
The 3S-12S input range is the headline figure. It means you can run the kit on everything from a small 3-cell pack up to a large 12-cell agricultural battery without adding a separate regulator for the controller itself. The flight controller logic runs on a narrow 4.8-5.3V rail, which is why the PMU matters: it steps the main pack voltage down to a clean 5V for the controller, GPS and LED modules.
The PMU 2 (UPS) input spans 11.1-50V and delivers a maximum of 3A at 5V. That headroom is useful on aircraft carrying several 5V accessories. The accuracy figures, ±1.5m horizontal and ±0.5m vertical, describe expected positioning performance, and the 6m/s vertical speed limit and 150 degrees per second yaw rate set the envelope the controller is rated for.
The 30-degree step angle and tilt angle figure describes the attitude range the controller expects during setup. Wind resistance is rated at wind force 4 with gusts to 5, so plan flights accordingly.
Compatibility and Requirements
The kit is designed around S.Bus receivers. Configuration is carried out on a Windows PC running Windows 7, 8 or 10 in either 32-bit or 64-bit versions. GPS and LED accessories are specified to run on 5V. The main PMU requires an 11.1V or higher input, and PMU 2 accepts 11.1-50V with a 3S-12S LiPo recommended.
Typical Uses
Because of the high voltage range and multi-rotor flexibility, the K++ V2 suits agricultural spray aircraft, survey and mapping drones, and larger camera-lift platforms. It is equally at home on a six-rotor heavy lifter or an eight-rotor redundant frame where the extra motor count improves safety.
What's in the Box
The package includes one Jiyi K++ V2 Flight Controller Kit.
Quick specs
- Item Type
- Kit
- Supported
- I4 , X4 four rotor ,iy6 , y6 , 16 , v6 six rotor v8 i8 x8 ix8 8 rotor
- Battery Type
- 3s -12s lithium polymer battery
- Receiver Type
- Sbus receiver
- OS Supports
- windows 7,8,10( 32 bit and 64 bit)
- Accuracy
- Horizontal direction : ±1.5m vertical direction ±0.5m
















