Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact MinimOSD-style board that overlays MAVLink telemetry from Pixhawk and APM controllers onto your analogue FPV video. It gives you live flight data on screen without needing a laptop in the field.

Key Highlights

  • MAX7456 monochrome on-screen display chip for clean video overlay
  • ATmega328P with Arduino bootloader for easy firmware work
  • Two independent power sections, each with its own LED indicator
  • Onboard +5V 500mA regulator accepts up to +12V input
  • Solder jumpers for combining power rails and selecting PAL video
  • Compact 58 x 22 mm board weighing about 15 g

Ideal For

  • FPV fixed-wing pilots wanting telemetry on their video feed
  • Multirotor builders using Pixhawk or APM autopilots
  • Pilots who fly without a laptop at the field
  • Makers comfortable with soldering and firmware flashing

Buying Tip

Confirm whether your unit ships with or without the casing before ordering, and remember to unplug USB from an APM 2 board before connecting the OSD.

Elecvora expert review

Our verdict

A practical, low-cost telemetry overlay for APM and Pixhawk builds that does its job without extra hardware. The dual power sections and onboard regulator make wiring flexible, though you should expect some soldering and firmware setup.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • MAX7456 overlay chip with proven reliability
  • Arduino-bootloader ATmega328P is easy to reflash
  • Dual power sections with LED indicators and jumpers
  • Onboard 5V regulator handles up to 12V input
  • Compact and light at about 15 g

Cons

  • Casing may or may not be included
  • Requires soldering for jumpers and some connections
  • Cannot be used while an APM 2 board is connected over USB

Best for

FPV pilots running Pixhawk or APM autopilots who want on-screen telemetry

Not ideal for

Plug-and-play users who want a fully cased, solder-free solution

Specifications

Item TypeModule
Cable Length100
Length (mm)58
Width (mm)22
Weight (g)15
Shipping Weight0.018 kg
Shipping Dimensions6 × 5 × 2 cm

What's in the box

  • 1 x Mini OSD for Pixhawk Flight Controller module
  • 1 x Connecting cables

Frequently Asked Questions

Which flight controllers does this OSD work with?
It is listed as compatible with APM2.5, APM2.6, APM2.8, Pixhawk and PX4 controllers.
Can I connect the OSD while my APM 2 is plugged into USB?
No. The OSD and USB share the same port on APM 2 boards, so disconnect the USB cable before connecting the OSD.
What input voltage can the board take?
The onboard regulator provides +5V at 500mA from a supply of up to +12V.
Does it support PAL video?
Yes, a solder jumper lets you select the PAL video option.
What comes in the package?
You receive one Mini OSD module and one set of connecting cables. The module may arrive with or without a casing.
How do I update the firmware?
Use the FTDI-compatible pinout or the standard 6-pin ISP header to program the ATmega328P, which ships with an Arduino bootloader.

Overview

The Mini OSD for Pixhawk Flight Controller is a small companion board that pulls MAVLink telemetry from your autopilot and writes it over your live video signal. Instead of opening Mission Planner on a laptop at the field, you get the key numbers on your goggles or monitor while you fly. It is aimed at FPV pilots and builders running APM or Pixhawk-class controllers who want a lightweight, low-cost telemetry overlay.

Key Features

  • MAX7456 OSD chip: handles the monochrome character overlay on your analogue video.
  • ATmega328P with Arduino bootloader: familiar platform for flashing and customising firmware.
  • FTDI-compatible pinout: standard serial header layout for configuration.
  • Standard 6-pin ISP header: allows direct in-circuit programming.
  • Dual power sections: two separate supplies, each with an LED indicator, plus solder jumpers to combine them.
  • Onboard regulator: +5V 500mA output from a supply of up to +12V.
  • PAL option: solder jumper lets you select the PAL video standard.
  • Test points: exposed HSYNC and LOS pads for diagnostics.

Specifications Explained

At roughly 58 mm long and 22 mm wide, the board fits into tight frames and stacks without crowding your wiring. The 15 g weight keeps it negligible in the build. A 100 mm connecting cable is included, which is enough for short runs between the OSD and your controller in most compact installations. The two independent power sections matter because OSD boards are often powered from both the flight controller side and the video side; keeping them separate avoids ground loops, and the jumpers let you tie them together when your setup allows it. The +5V 500mA regulator means you can feed the board from a supply up to +12V without adding an external BEC.

Compatibility and Requirements

The module is listed as compatible with APM2.5, APM2.6, APM2.8, Pixhawk and PX4 flight controllers. One important restriction: do not connect the OSD while your APM 2 board is also connected over USB, because they share the same port. Unplug the USB cable from the APM 2 before using the OSD. The product may arrive with or without a casing, so check the listing photos before you plan your mounting.

Typical Uses

Use it on FPV fixed-wing and multirotor builds where you want altitude, speed, battery voltage and mode information visible in the video feed. It also suits pilots who fly at locations without a laptop and still want telemetry confirmation during the flight.

What's in the Box

  • 1 x Mini OSD for Pixhawk Flight Controller module
  • 1 x Connecting cables

Quick specs

Item Type
Module
Cable Length
100
Length (mm)
58
Width (mm)
22
Weight (g)
15
Shipping Weight
0.018 kg
See all specifications