
1 / 2 · Click to enlarge
At a glance
Made by LiteWing, this drone frames is a good fit for makers, students and electronics hobbyists. Main specs: microcontroller ESP32-S3 (Dual-core Xtensa LX7, 240 MHz, 512 KB SRAM); batteries required 3.7V 1S LiPo Battery 20C or higher; circuit type TP4056 Li-ion Charging IC (1A Max)(chariging circuit). Check that your power source supplies SPX3819, 500mA, Low Noise LDO before connecting it.
Key Highlights
- Microcontroller: ESP32-S3 (Dual-core Xtensa LX7, 240 MHz, 512 KB SRAM)
- Batteries Required: 3.7V 1S LiPo Battery 20C or higher
- Circuit Type: TP4056 Li-ion Charging IC (1A Max)(chariging circuit)
Ideal For
- Arduino, ESP32 and Raspberry Pi projects
- School and college lab work
- Prototypes and test rigs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Microcontroller | ESP32-S3 (Dual-core Xtensa LX7, 240 MHz, 512 KB SRAM) |
|---|---|
| Motor Type | 720 Coreless DC Motors |
| Batteries Required | 3.7V 1S LiPo Battery 20C or higher |
| Circuit Type | TP4056 Li-ion Charging IC (1A Max)(chariging circuit) |
| Voltage Regulator | SPX3819, 500mA, Low Noise LDO |
| Communication | WiFi 2.4GHz |
| Communication Protocol | CRTP over UDP |
| Interface | USB Type-C (CH340 USB to UART bridge)(Programming Interface) |
| Motor Control | MOSFET-based PWM Speed Control |
| Propeller | 65 |
| Expansion Port | 24Pin GPIO Breakouts for Additional Sensors, SMD Solder pads for Popular sensors on the PCB bottom |
| LED Indicator | Power Indicator, Charging Indicator, Full Charge Indicator, System Status Indicator, Link Status Indicator, Error Indicator |
| Audio input/output Port | Connector for optional Passive buzzer for audio indications |
| Max Capacity | ~25g with 55mm propeller(payload) |
| Length (mm) | 100 |
| Width (mm) | 100 |
| Weight (g) | (without battery), 45 |
| Shipping Weight | 0.126 kg |
| Shipping Dimensions | 18 × 14 × 6 cm |
Overview
The LiteWing -Circuit Digest ESP32 Based Programmable Drone Development Board with Battery, made by LiteWing, is listed in our drone frames range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Microcontroller: ESP32-S3 (Dual-core Xtensa LX7, 240 MHz, 512 KB SRAM) (look up this chip to confirm it runs the firmware or libraries you plan to use)
- Motor Type: 720 Coreless DC Motors
- Batteries Required: 3.7V 1S LiPo Battery 20C or higher (note the battery type so you can order spares or the right charger)
- Circuit Type: TP4056 Li-ion Charging IC (1A Max)(chariging circuit) (check which plug or cable it needs)
- Voltage Regulator: SPX3819, 500mA, Low Noise LDO (match this to your power supply; too high a voltage can damage the part)
- Communication: WiFi 2.4GHz (2.4 GHz reaches further, 5 GHz is faster at short range)
- Communication Protocol: CRTP over UDP
- Interface: USB Type-C (CH340 USB to UART bridge)(Programming Interface) (confirm your cable or board uses the same connector)
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
LiteWing is an innovative ESP32-S3–powered programmable drone designed for makers, developers, and educators. Combining the power of open hardware with Wi-Fi connectivity, it lets you experiment, code, and fly using your smartphone or PC. Its lightweight PCB frame and efficient 720 coreless motors make it agile and affordable, while sensors like the MPU6050 ensure stable flight. With support for Crazyflie cfclient and Python SDK, LiteWing encourages creativity—add height hold, position hold, or gesture control easily. Whether you’re learning drone technology or building custom flight applications, LiteWing offers a ready-to-fly, fully open-source platform for limitless innovation.
Note: Propeller color may vary from the actual product.

Features:
- ESP32-S3 dual-core microcontroller with Wi-Fi & Bluetooth
- Open-source Crazyflie-based firmware with Python SDK support
- Wi-Fi smartphone control – no external transmitter needed
- Expandable GPIO pins for extra sensors and modules
- Lightweight PCB frame with onboard charger and LED indicators
- Easy USB Type-C programming and firmware flashing
Package Includes:
1 x Circuit Digest - LiteWing - ESP32 based Programmable Drone Development Board with Battery for Makers, Developers and Educators (Ready to Fly)Quick specs
- Microcontroller
- ESP32-S3 (Dual-core Xtensa LX7, 240 MHz, 512 KB SRAM)
- Motor Type
- 720 Coreless DC Motors
- Batteries Required
- 3.7V 1S LiPo Battery 20C or higher
- Circuit Type
- TP4056 Li-ion Charging IC (1A Max)(chariging circuit)
- Voltage Regulator
- SPX3819, 500mA, Low Noise LDO
- Communication
- WiFi 2.4GHz













