Skip to main content

Worldwide Shipping · Secure Payments

At a glance

This other 3d printer accessories is a good fit for makers, students and electronics hobbyists. Main specs: item type Module; material Plastic, Metal; input voltage (vdc) Dec-50, 12 to 50. Check that your power source supplies Dec-50, 12 to 50 before connecting it.

Key Highlights

  • Item Type: Module
  • Material: Plastic, Metal
  • Input Voltage (VDC): Dec-50, 12 to 50

Ideal For

  • Upgrading or repairing a 3D printer
  • Spare parts for long prints
  • Testing new materials

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeModule
MaterialPlastic, Metal
Input Voltage (VDC)Dec-50, 12 to 50
Cable Length0.3
Length (mm)70
Width (mm)45
Weight (g)52
Size (mm)70x45
Shipping Weight0.057 kg
Shipping Dimensions8 × 3 × 2 cm

Overview

The MOS25 12 to 50V 25A 3D printer Heat Bed Power Expansion Module with Cables is listed in our other 3d printer accessories range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Module
  • Material: Plastic, Metal (affects weight, heat handling and how the part wears)
  • Input Voltage (VDC): Dec-50, 12 to 50 (match this to your power supply; too high a voltage can damage the part)
  • Cable Length: 0.3 (measure your mounting space before ordering)
  • Length (mm): 70 (measure your mounting space before ordering)
  • Width (mm): 45 (measure your mounting space before ordering)
  • Weight (g): 52 (important for drones, RC models and anything you carry)
  • Size (mm): 70x45 (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

MOS25 12 to 50V 25A 3D printer Heat Bed Power Expansion Module is based on power MOSFET and will allow PID control of 3D printer heat bed (DC-DC Relays usually do not allow this). The module has MKS MOSFET for RAMPS 1.4 Heating-Controller with Max Current capacity of 25A.  MOS25 can be stable long-term work when measured I (Max) = 25A. When using the module, the current should not exceed 25A. Note: When using hot bed power greater than 150W, an external high power module is needed.

Features:

  1. Application: with much larger heat sink, thereby operation without active cooling at higher currents possible suitable for anet a8, a6, a2; ramps; mk8; RepRap 3d printer
  2. Unique design: with unique snowflake heatsink design, it has a great cooling effect the heat bed power module can be used in both large motherboard and other 3d printer motherboards
  3. 30A max current: this high power module helps your 3d printer equipped with the lerdge controller board become even more powerful the module can solve the current load problem when the heated bed power is too large with this add-on module to board lead the maximum current up to 30a
  4. Good protection: when using heated bed 3d printer for 12v power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning

Package Includes:

1 x MOS25 12 to 50V 25A 3D printer Heat Bed Power Expansion Module

1 x Connecting Cables

Quick specs

Item Type
Module
Material
Plastic, Metal
Input Voltage (VDC)
Dec-50, 12 to 50
Cable Length
0.3
Length (mm)
70
Width (mm)
45
See all specifications