Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A subminiature OMRON snap-action limit switch with a light 0.49N plunger and 5A 125VAC contacts, sized for 3D printer endstop duty. Its 30 million cycle life makes it a dependable choice for repeated homing.

Key Highlights

  • Subminiature snap-action body measuring about 20 x 15 mm
  • Light 0.49N operating force for gentle, repeatable actuation
  • 5A at 125VAC contact rating suits endstop signal circuits
  • Rated for 30 million operations for long-term reliability
  • Weighs only 5 g, adding negligible load to moving parts
  • Supplied as a single switch without a pre-attached cable

Ideal For

  • 3D printer owners replacing a worn or unreliable axis endstop
  • Makers building compact motion systems needing a small snap-action switch
  • Repair technicians servicing desktop 3D printers
  • DIY CNC and automation builders adding limit detection

Buying Tip

Confirm your mount's plunger position and terminal spacing before ordering, since this is a bare switch with no cable or fixings included.

Elecvora expert review

Our verdict

A sensible, no-frills endstop choice: the light 0.49N actuation and 30 million cycle rating suit printers that home constantly, and the small body fits where bigger switches will not. Just plan for soldering and your own mounting hardware, because nothing else is in the box.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Low 0.49N operating force reduces load on lightweight carriages
  • 5A at 125VAC contact rating gives ample headroom for endstop signals
  • 30 million operation life supports frequent homing
  • Compact 20 x 15 mm body and 5 g weight

Cons

  • No cable or connector included, so soldering or terminating is required
  • Mounting hardware is not supplied
  • Bare switch only, so wiring must match your controller

Best for

3D printer and small motion-system builders who want a compact, long-life mechanical endstop

Not ideal for

Users wanting a plug-and-play endstop with pre-crimped cable and bracket

Specifications

Item TypeGeneral Limit Switch
With Cable (Y/N)No
Operating force0.49N
Life Cycle30 Million
Length (mm)20
Width (mm)15
Current Rating (A)5A
Weight (g)5
Voltage Rating (V)125 VAC
Shipping Weight0.01 kg
Shipping Dimensions5 × 5 × 3 cm

What's in the box

  • 1 x OMRON SS-5GL 3D Printer Limit Switch Endstop

Frequently Asked Questions

What is this switch used for on a 3D printer?
It is typically used as an axis endstop, signalling the controller when the carriage or bed reaches the end of its travel during homing. Its plunger is pressed by a striking surface at that point.
Does it come with a cable or connector?
No. The switch is supplied on its own with no cable attached, so you will need to solder or terminate your own wiring.
What voltage and current can it handle?
The contact rating is 5A at 125VAC. Endstop inputs draw very little current, so this leaves plenty of margin, but check your controller's input requirements before wiring.
How much force is needed to actuate it?
The operating force is 0.49N, which is light enough for small carriages and levers to trigger without noticeable resistance.
How long should it last?
The switch is rated for 30 million operations. Actual service depends on how often your machine homes and on correct mounting and alignment.
Will it fit my printer's existing endstop mount?
That depends on your bracket. The body is about 20 x 15 mm, so measure your mount and check plunger alignment before ordering.

Overview

The OMRON SS-5GL is a subminiature general-purpose limit switch in a snap-action format. In 3D printing it is most often used as an endstop: a small mechanical switch that tells the controller when an axis has reached the end of its travel during homing. The plunger design and low 0.49N operating force let it trigger with very little pressure, which matters on lightweight carriages and small mechanisms where extra force could deflect the part being sensed.

The switch is compact at approximately 20 mm long and 15 mm wide, and it weighs around 5 g. That makes it easy to mount on crowded gantry plates, bed supports and extruder carriages. It ships as a bare switch with no cable attached, so you can solder or terminate it to suit your own wiring layout.

Key Features

  • Snap-action mechanism: fast, clean contact transfer at the actuation point rather than a slow make-or-break.
  • Low actuation force: 0.49N keeps the pressure on your moving assembly minimal.
  • Solid contact rating: 5A at 125VAC covers typical low-current endstop signalling with margin.
  • Long service life: rated for 30 million operations, useful on machines that home before every job.
  • Small footprint: a 20 x 15 mm body and 5 g weight suit tight, lightweight builds.

Specifications Explained

Operating force: 0.49N

This is the pressure needed to actuate the plunger. A figure this low means the switch will not fight the carriage or lever that presses it, reducing the chance of missed triggers or mechanical flex at the end of travel.

Contact rating: 5A at 125VAC

The contact rating describes the load the switch can carry. Endstop inputs on 3D printer controllers draw very little current, so this rating leaves comfortable headroom. Match your wiring and controller input requirements to the switch before connecting it.

Life cycle: 30 million operations

This is the manufacturer's mechanical endurance figure. On a printer that homes several times a day, it translates into a long service interval before replacement is likely.

Size and weight

At roughly 20 x 15 mm and 5 g, the switch adds little mass and needs only a small mounting area. Confirm clearance for the plunger travel and your chosen terminals in your own design.

Compatibility and Requirements

This listing is for the switch only. No cable, connector or mounting hardware is included, so you will need to solder or terminate wires yourself and provide your own fasteners. Check that your controller's endstop input and wiring suit a mechanical switch of this type, and verify that the 20 x 15 mm body and plunger position fit your mount before installation.

Typical Uses

  • Axis endstops on 3D printer gantries and beds
  • Position sensing on small linear mechanisms and automation projects
  • Limit detection in DIY CNC and motion-control builds
  • Replacement switch for an existing endstop mount

What's in the Box

One OMRON SS-5GL 3D printer limit switch endstop. Cable and mounting fixings are not supplied.

Quick specs

Item Type
General Limit Switch
With Cable (Y/N)
No
Operating force
0.49N
Life Cycle
30 Million
Length (mm)
20
Width (mm)
15
See all specifications