Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by openMV, this smart vision cameras is a good fit for everyday home and hobby use. Main specs: item type Accessory; host interface SPI; rating voltage (vdc) 2.7 to 3.6. Check that your power source supplies 2.7 to 3.6 before connecting it.

Key Highlights

  • Item Type: Accessory
  • Host Interface: SPI
  • Rating Voltage (VDC): 2.7 to 3.6

Ideal For

  • Everyday use

Buying Tip

Read the full specifications and the package contents list below to make sure it does what you need.

Specifications

Item TypeAccessory
Host InterfaceSPI
Rating Voltage (VDC)2.7 to 3.6
Operating Temperature (°C)-40°C to 85°C
Operating humidity10% to 95% Non-Condensing
Dimensions (L x W x H) mm35 x 25 x 10
Shipping Weight0.008 kg
Shipping Dimensions12 × 8 × 2 cm

Overview

The OpenMV WiFi Shield, made by openMV, is listed in our smart vision cameras range and suits everyday home and hobby use. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Accessory
  • Host Interface: SPI (confirm your cable or board uses the same connector)
  • Rating Voltage (VDC): 2.7 to 3.6 (match this to your power supply; too high a voltage can damage the part)
  • Operating Temperature (°C): -40°C to 85°C
  • Operating humidity: 10% to 95% Non-Condensing
  • Dimensions (L x W x H) mm: 35 x 25 x 10 (measure your mounting space before ordering)
  • Shipping Weight: 0.008 kg (important for drones, RC models and anything you carry)
  • Shipping Dimensions: 12 × 8 × 2 cm (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

The ATWINC1510-MR210xB is a low power consumption 802.11 b/g/n IoT (Internet of Things) module,specifically optimized for low power IoT applications. The module integrates Power Amplifier (PA), Low-Noise Amplifier (LNA), Switch, Power Management, and a printed antenna or a micro co-ax (u.FL) connector for an external antenna resulting in a small form factor (21.7 x 14.7 x 2.1 mm) design. It is interoperable with various vendors’ 802.11 b/g/n access points. This module provides SPI ports to interface with a host controller. Application : The WiFi Shield is great for turning your OpenMV Cam into a Web Cam. With the WiFi Shield you'll be able to stream JPEG compressed images to connecting Web Browsers like FireFox. Once the WiFi Shield is connected to the internet you'll be able to send and receive data over TCP/UDP ports using MicroPython's BSD socket low-level network interface.  

Features:

  1. IEEE® 802.11 b/g/n 20 MHz (1x1) solution
  2.  Single spatial stream in 2.4 GHz ISM band
  3. Integrated Transmit/Receive switch
  4. Integrated PCB antenna or u.FL micro co-ax connector for external antenna
  5.  Superior sensitivity and range via advanced PHY signal processing
  6.  Advanced equalization and channel estimation
  7. Advanced carrier and timing synchronization
  8. Wi-Fi® Direct (supported till firmware release 19.5.2)
  9. Soft-AP support
  10.  Supports IEEE 802.11 WEP, WPA, WPA2 security
  11.  Support Enterprise security with WPA/WPA2 (802.1X)(1) – EAP-TLS – EAP-PEAPv0/1 with TLS – EAP-TTLSv0 with MSCHAPv2 – EAP-PEAPv0/1 with MSCHAPv2 • Superior MAC throughput via hardware accelerated two-level A-MSDU/A-MPDU frame aggregation and block acknowledgment • On-chip memory management engine to reduce host load • SPI host interface

Package Includes:

1 x OpenMV WiFi Shield

Quick specs

Item Type
Accessory
Host Interface
SPI
Rating Voltage (VDC)
2.7 to 3.6
Operating Temperature (°C)
-40°C to 85°C
Operating humidity
10% to 95% Non-Condensing
Dimensions (L x W x H) mm
35 x 25 x 10
See all specifications