
1 / 6 · Click to enlarge
AI Summary
The Radiomaster RP1 V2 is a nano ExpressLRS receiver for 2.4GHz systems, weighing just 2.2g with its antenna. It offers 500Hz/F1000Hz refresh rates and a CRSF interface for low-latency control in compact FPV builds.
Key Highlights
- 2.4GHz ExpressLRS receiver with 500Hz and F1000Hz refresh rates
- Ultra-compact 13 x 11 x 3mm board weighs 2.2g including antenna
- Pre-installed ExpressLRS v2.4 firmware with CRSF interface
- Improved PCB design for better heat dissipation
- Rigid UFL T-antenna and top-side LED for easy setup
- Built-in TCXO for stable frequency control
Ideal For
- FPV drone pilots building lightweight 2.4GHz ExpressLRS quads
- RC car and boat hobbyists needing a compact receiver
- Micro and nano build enthusiasts with limited space
- Pilots upgrading to ExpressLRS for low-latency control
Buying Tip
Confirm your transmitter or module supports 2.4GHz ExpressLRS and that your flight controller has a free 5V pad and CRSF-capable UART before buying.
Elecvora expert review
Our verdict
The Radiomaster RP1 V2 is a well-executed nano ExpressLRS receiver that balances size, weight, and features. Its improved PCB, rigid antenna, and easy solder pads make it a practical choice for compact builds.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Very small and light at 2.2g including antenna
- Pre-installed ExpressLRS v2.4 firmware
- Selectable 500Hz/F1000Hz refresh rates
- Improved heat dissipation and solder pads
- Built-in TCXO for stable frequency control
Cons
- Requires soldering to connect power and signal
- Only 5V input, so a suitable 5V source is needed
- No detailed range or telemetry specifications provided
Best for
FPV pilots and RC hobbyists building lightweight 2.4GHz ExpressLRS systems
Not ideal for
Users who need a plug-and-play receiver with pre-attached connectors or non-ExpressLRS systems
Specifications
| Item Type | Receiver |
|---|---|
| Frequency (GHz) | 2.4 |
| Refresh Rate (Hz) | 500Hz / F1000Hz |
| Operating Voltage (V) | 5V |
| Weight (g) | 2.2g (Including antenna) |
| Dimensions (L x W x H) mm | 13mm x 11mm x 3mm |
| Firmware Version | ExpressLRS v2.4 per-installed |
| Interface | CRSF |
| Shipping Weight | 0.011 kg |
| Shipping Dimensions | 10 × 9 × 1 cm |
What's in the box
- 1 x RP1 ExpressLRS 2.4GHz Nano Receiver
- 1 x 65mm UFL 2.4GHz T Antenna
- 1 x User Manual
- 1 x CRSF Wire
Frequently Asked Questions
What firmware comes pre-installed on the RP1 V2?
What input voltage does the receiver require?
Which transmitters and modules are compatible?
What is included in the package?
What refresh rates are supported?
How should I care for the receiver?
Overview
The Radiomaster RP1 V2 ExpressLRS Nano Receiver is a 2.4GHz radio receiver designed for FPV drones and RC vehicles where every gram and millimetre counts. At just 13 x 11 x 3mm and 2.2g including its antenna, it fits into tight builds without adding noticeable weight. It runs pre-installed ExpressLRS v2.4 firmware and uses a CRSF interface, making it a straightforward choice for pilots already using ExpressLRS.
Key Features
- ExpressLRS 2.4GHz: Works with any 2.4GHz ExpressLRS module or transmitter with built-in 2.4GHz ExpressLRS.
- Selectable refresh rates: Supports 500Hz and F1000Hz for responsive control.
- Improved PCB: Better heat dissipation helps maintain stable operation.
- Rigid antenna: Upgraded UFL T-antenna offers greater durability and performance.
- Top-side LED: Makes status checks easier during setup and flight.
- Easier soldering: Redesigned solder pads simplify wiring.
- Built-in TCXO: Temperature-compensated crystal oscillator supports consistent frequency control.
Specifications Explained
The 2.4GHz frequency band is widely used for RC control and is supported by ExpressLRS systems. The 500Hz and F1000Hz refresh rates refer to how often the receiver updates control inputs; higher rates can reduce latency in demanding flying. Operating voltage is 5V, so the receiver must be powered from a 5V source. Its CRSF interface is a common serial protocol for connecting to flight controllers. The 2.2g weight includes the antenna, and the compact dimensions make it suitable for nano builds.
Compatibility and Requirements
The RP1 V2 is compatible with all 2.4GHz ExpressLRS modules and transmitters with built-in 2.4GHz ExpressLRS. It requires a 5V power supply and a flight controller or device that accepts a CRSF signal. No other compatibility details are specified.
Typical Uses
This receiver is suited to FPV drones, RC cars, boats, and other small radio-controlled models where a lightweight 2.4GHz ExpressLRS link is needed. Its small size makes it a good fit for micro and nano builds, as well as larger craft where saving weight is a priority.
What's in the Box
- 1 x RP1 ExpressLRS 2.4GHz Nano Receiver
- 1 x 65mm UFL 2.4GHz T Antenna
- 1 x User Manual
- 1 x CRSF Wire
Quick specs
- Item Type
- Receiver
- Frequency (GHz)
- 2.4
- Refresh Rate (Hz)
- 500Hz / F1000Hz
- Operating Voltage (V)
- 5V
- Weight (g)
- 2.2g (Including antenna)
- Dimensions (L x W x H) mm
- 13mm x 11mm x 3mm
















