Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 100 mm four-pin replacement cable for TF Mini and TF Mini S LiDAR sensors, with a 1 mm pitch and a lightweight 2 g build. It lets you replace a lost or damaged lead without replacing the sensor itself.

Key Highlights

  • 100 mm cable length for short, tidy sensor runs
  • Four-pin connector with 1 mm pitch
  • Compact 6.5 mm wide connector body
  • Weighs about 2 g, ideal for weight-sensitive builds
  • Direct replacement lead for TF Mini and TF Mini S
  • Light shipping weight of 0.005 kg

Ideal For

  • Drone builders using TF Mini or TF Mini S LiDAR
  • RC hobbyists replacing a damaged sensor lead
  • Makers and students working with LiDAR distance sensing
  • Service technicians keeping spare sensor cables
  • FPV and robotics hobbyists with weight-sensitive builds

Buying Tip

Before ordering, count the pins and measure the pitch on your sensor and controller connector to confirm the 1 mm, four-pin fit.

Elecvora expert review

Our verdict

A sensible, low-cost spare for anyone running a TF Mini or TF Mini S. It does one job, reconnecting the sensor, and does it in a compact 100 mm form.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Correct four-pin, 1 mm pitch format for the listed sensors
  • Short 100 mm length keeps wiring neat
  • Very light at about 2 g
  • Small and easy to store as a spare

Cons

  • Only suits hardware with a matching four-pin, 1 mm pitch connector
  • Package contents are not confirmed in the product data
  • Short length limits mounting distance

Best for

Owners of TF Mini or TF Mini S sensors who need a replacement or spare lead

Not ideal for

Sensors or boards that use a different pin count or pitch

Specifications

Cable Length100
No. of Pins4
Pitch (mm)1
Length (mm)100
Width (mm)6.5
Weight (g)2
Shipping Weight0.005 kg
Shipping Dimensions4 × 4 × 2 cm

Frequently Asked Questions

Which sensors is this cable for?
It is listed as a replacement cable for the TF Mini and TF Mini S LiDAR sensors.
What is the pin pitch?
The cable has four pins with a 1 mm pitch, and the connector body is 6.5 mm wide.
How long is the cable?
The cable is 100 mm long, which suits installations where the sensor sits close to the controller.
How much does it weigh?
The cable weighs about 2 g, and the listed shipping weight is 0.005 kg.
How many cables are included?
Package contents are not specified in the product data, so confirm the quantity with the listing before ordering.
How should I care for the cable?
Power down before connecting or disconnecting, avoid pulling on the lead, and keep the connector free of dust and moisture.

Overview

This is a replacement four-pin cable for the TF Mini and TF Mini S LiDAR distance sensors. It is a spare part rather than an upgrade: the job is simply to reconnect the sensor to your controller when the original lead has been lost, damaged or shortened during a rebuild. The cable measures 100 mm, which suits installations where the sensor and its controller sit close together and long runs would only add clutter.

Key Features

  • Four-pin lead intended for TF Mini and TF Mini S LiDAR sensors
  • 100 mm length for compact, close-coupled wiring
  • 1 mm pin pitch for a precise fit on the matching header
  • Connector body just 6.5 mm wide
  • Approximately 2 g in weight, so it barely affects payload

Specifications Explained

Cable length: 100 mm is a short lead. It is best for builds where the LiDAR sits near the flight controller or mainboard. If your sensor is mounted further away, plan the routing so the cable is not under tension.

Pin count and pitch: Four pins at a 1 mm pitch define the connector footprint. Check that your sensor and board use a matching four-pin, 1 mm pitch connection before ordering, because pitch is what decides whether a plug seats correctly.

Size and weight: The connector body is 6.5 mm wide, and the whole cable weighs about 2 g. That is light enough for small drones and handheld instruments where every gram counts.

Shipping figures: Shipping weight is listed at 0.005 kg and shipping dimensions at 4 x 4 x 2 cm, so the part arrives as a small, easily stored spare.

Compatibility and Requirements

This cable is listed for the TF Mini and TF Mini S LiDAR sensors. Fit depends on the four-pin, 1 mm pitch connector on your hardware. Confirm the pin arrangement and connector type on your sensor and controller before use, since the product data does not list adapter boards or other devices.

Typical Uses

Use it to replace a damaged lead on a drone or RC model carrying a TF Mini sensor, to keep a spare in a field kit, or to rewire a bench setup where the original cable was cut short. It also suits anyone servicing LiDAR units who wants a spare on hand.

What's in the Box

Package contents are not specified in the product data. Check the listing details before ordering if you need to confirm the exact quantity supplied.

Quick specs

Cable Length
100
No. of Pins
4
Pitch (mm)
1
Length (mm)
100
Width (mm)
6.5
Weight (g)
2
See all specifications