Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 24 V brushless DC centrifugal pump delivering 12 L/min and up to 8 m of head with a magnetic-drive seal that eliminates shaft-seal leaks. It runs continuously, stays under 40 dB, and handles hot water up to 100°C.

Key Highlights

  • Magnetic-drive static seal for leak-free, maintenance-light operation
  • 12 L/min flow rate with 8 m maximum head at 24 V DC
  • Brushless motor rated for 24/7 continuous running
  • Handles hot water up to 100°C with FDA-standard wetted materials
  • Quiet operation under 40 dB with a balanced closed-type impeller
  • Compact 45.9 mm body, 84.9 mm long, 221 g

Ideal For

  • Electronics builders assembling liquid cooling loops
  • Prototype and test rig engineers needing continuous circulation
  • Small-system designers working with hot water up to 100°C
  • Makers replacing mains pumps with a compact 24 V DC unit
  • Equipment integrators who need quiet, low-maintenance fluid movement

Buying Tip

Check your loop's restriction before buying: the 8 m maximum head is a shut-off figure, so expect noticeably less than 12 L/min once tubing, fittings and a cold plate are in the path.

Elecvora expert review

Our verdict

A well-considered little pump for builders who value a seal-free design and continuous-duty running over raw pressure. The 12 L/min and 8 m figures suit modest loops, and the 100°C fluid rating plus FDA-standard wetted materials widen its usefulness.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Magnetic-drive static seal removes the usual leak point
  • Rated for 24/7 continuous operation
  • Quiet at under 40 dB
  • Handles hot water up to 100°C
  • Compact and light at 221 g

Cons

  • Requires a separate 24 V DC supply
  • 8 m maximum head limits use in highly restrictive loops
  • No port or connector details are specified in the listing

Best for

Compact 24 V DC circulation loops needing quiet, continuous, leak-free operation

Not ideal for

High-pressure or long-run systems that need far more than 8 m of head

Specifications

Item TypeCentrifugal Pump
Model No. / NameTL B10 C24 1208
Flow Rate (LPM)12
Rated Voltage (VDC)24 DC
Motor TypeBrushless DC Motor
Ambient Temperature (°C)-40-40
Rated Power (W)31.2
Noise (dB)< 40
Max Head(m)8
Length (mm)84.9
Diameter (mm)45.9
Weight (g)221
Shipping Weight0.298 kg
Shipping Dimensions14 × 12 × 9 cm

What's in the box

  • 1 x TOPSFLO Brushless DC Centrifugal Pump TL-B10-C24-1208

Frequently Asked Questions

What voltage does this pump need?
It is rated for 24 V DC only. Connect it to a regulated 24 V DC supply that can cover the 31.2 W rated power with some margin.
Can it run all the time?
Yes. The brushless motor is designed for 24/7 continuous working conditions, which is one of its main advantages over brushed alternatives.
How much flow will I actually get?
The rated flow is 12 L/min and the maximum head is 8 m. Real flow depends on how restrictive your loop is, and it drops as resistance increases.
Can it handle hot water?
The pump is rated for hot water up to 100°C. Keep in mind that the -40 to 40°C figure refers to ambient temperature around the pump, not the fluid.
What comes in the box?
One TOPSFLO Brushless DC Centrifugal Pump TL-B10-C24-1208. Check the attachments section for the datasheet before installing.
Does it need much maintenance?
Very little. Because the impeller is driven magnetically through a static seal, there is no shaft seal to wear out or replace as part of routine service.

Overview

The TOPSFLO TL-B10-C24-1208 is a small brushless DC centrifugal pump intended for builders who need reliable liquid circulation inside a compact enclosure. Instead of a conventional shaft seal, the impeller is driven magnetically through a static seal, which removes the usual leak path and the wear part that goes with it. A permanent-magnet rotor and a precision-balanced impeller keep rotation smooth, and the closed-type impeller design supports steady flow rather than turbulence.

Powered from a 24 V DC supply, the pump draws 31.2 W and delivers a 12 L/min flow rate against a maximum head of 8 m. It is rated for continuous operation, so it can stay running for long unattended cycles, and it tolerates hot water up to 100°C. Wetted materials meet FDA standards, which broadens the range of fluids it can be used with.

Key Features

  • Magnetic-drive static seal: no rotating shaft seal to leak or replace.
  • Brushless DC motor: built for 24/7 continuous duty with low maintenance.
  • Balanced closed-type impeller: smooth, stable circulation with reduced noise.
  • Quiet running: noise level below 40 dB.
  • Hot water capable: rated for fluids up to 100°C.
  • FDA-standard wetted materials: suitable for sensitive fluid paths.
  • Compact footprint: 45.9 mm diameter and 84.9 mm length at 221 g.

Specifications Explained

Flow and head are the two numbers that decide whether a pump suits a loop. A 12 L/min flow rate with an 8 m maximum head means the pump is happiest moving moderate volumes through reasonably open paths; as restriction rises, flow falls toward zero at the 8 m limit. Plan tubing and fittings with that trade-off in mind.

24 V DC and 31.2 W define the power side. The pump expects a regulated 24 V DC source capable of supplying the rated power with margin. Under 40 dB keeps it unobtrusive in enclosures near living or working spaces.

Temperature range of -40 to 40°C refers to ambient conditions around the pump, while the fluid path is rated for hot water up to 100°C. Keep the two figures separate when planning an installation.

Compatibility and Requirements

The pump requires a 24 V DC power supply; no other voltage is specified for this model. It is a standalone circulation pump, not a drop-in replacement for a mains-powered unit, and it needs to be wired into your own DC circuit. Confirm that your tubing and fittings match the pump's ports before installation, and mount it where ambient temperature stays within the stated range.

Typical Uses

  • Electronics and equipment cooling loops
  • Hot water circulation in small systems
  • Fluid transfer in compact enclosures and prototypes
  • Circulation where FDA-standard wetted materials matter

What's in the Box

1 x TOPSFLO Brushless DC Centrifugal Pump TL-B10-C24-1208. Refer to the datasheet in the attachments section for further product details.

Quick specs

Item Type
Centrifugal Pump
Model No. / Name
TL B10 C24 1208
Flow Rate (LPM)
12
Rated Voltage (VDC)
24 DC
Motor Type
Brushless DC Motor
Ambient Temperature (°C)
-40-40
See all specifications