Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A two-piece set of aluminium GT2 idler pulleys with 20 teeth and a 5mm bore, made for 6mm wide timing belts. The dual-bearing design keeps the pulley spinning freely so belt tension stays smooth.

Key Highlights

  • Aluminium GT2 idler pulley with 20 teeth for 6mm wide belts
  • 5mm bore fits a standard 5mm shaft or bolt
  • Dual bearings inside each pulley for free rotation
  • 18mm outer diameter and 8.5mm width
  • Lightweight at about 6g per pulley
  • Two pulleys included in the pack

Ideal For

  • 3D printer builders tensioning GT2 belts
  • DIY CNC and motion system makers
  • Makers replacing printed idler wheels
  • Hobbyists maintaining belt-driven machines
  • Anyone needing a 5mm bore GT2 idler

Buying Tip

Confirm your belt is 6mm wide GT2 and your mounting shaft or bolt is 5mm before ordering, since the bore and belt width are fixed on this part.

Elecvora expert review

Our verdict

A small, well-made metal idler that solves a common problem in belt-driven builds: keeping the belt running on a concentric, free-spinning surface. It is a sensible, low-cost part for anyone already working with 6mm GT2 belts and 5mm mounting hardware.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Aluminium body with a clean silver finish
  • Dual bearings for free rotation
  • Correct 20-tooth GT2 profile for 6mm belts
  • Compact and lightweight at about 6g
  • Two pulleys in one pack

Cons

  • Only suits 6mm GT2 belts and 5mm bores
  • No mounting hardware included
  • Unbranded part with no stated warranty

Best for

3D printer and DIY motion builders using 6mm GT2 belts

Not ideal for

Builds using wider belts or shafts other than 5mm

Specifications

Item TypeTiming Pulley
Compatibilityfor 6mm belt, 6mm Belt
MaterialAluminium
Inner Diameter (mm)5
Outer Diameter (mm)18
No. of Teeth20
No. of Bearings2
Width (mm)8.5
ColorSilver
Weight (g)6
Shipping Weight0.01 kg
Shipping Dimensions4 × 3 × 2 cm

What's in the box

  • 2 x Two Trees Aluminum GT2 Timing Idler Pulley, 20 tooth, 5mm bore

Frequently Asked Questions

What belt width does this pulley fit?
It is made for 6mm wide GT2 timing belts. The 20-tooth profile is matched to that belt type.
What is the bore size?
The inner diameter is 5mm, so it mounts on a 5mm shaft, bolt or axle.
Does it come with bearings?
Yes. Each pulley contains two bearings, giving a total of four bearings across the two-pulley pack.
How many pulleys are included?
The pack contains two idler pulleys.
Is this a driven pulley or an idler?
It is an idler pulley, used to guide and tension the belt. It pairs with a 20-tooth GT2 driving pulley in the same belt system.
How should I care for it?
Keep the teeth clean and check that the bearings spin freely. Replace the pulley if rotation becomes rough or the belt shows uneven wear.

Overview

These Two Trees GT2 idler pulleys are designed to guide and tension 6mm wide GT2 timing belts in belt-driven builds. Each pulley has 20 teeth, a 5mm bore and an 18mm outer diameter, and is machined from aluminium with a silver finish. Two bearings are fitted inside every pulley, so the part rotates around a fixed shaft rather than being clamped in place.

That bearing arrangement is what makes an idler pulley useful: the belt runs against a smooth, concentric surface while the pulley spins freely, which helps reduce friction and vibration compared with printed wheels or washer-clamped setups. The set contains two pulleys, each weighing about 6g.

Key Features

  • Aluminium body: a machined metal pulley that holds its shape under belt tension.
  • 20-tooth GT2 profile: matched to GT2 belts that are 6mm wide.
  • 5mm bore: fits a 5mm shaft, axle or bolt for mounting.
  • Dual bearings: two bearings per pulley for free, low-friction rotation.
  • Compact size: 18mm outer diameter and 8.5mm width.
  • Two-piece pack: enough pulleys for a typical paired idler position.

Specifications Explained

Teeth and belt width: the 20-tooth GT2 profile is intended for 6mm wide GT2 timing belts, so the belt sits correctly in the tooth grooves. Bore: the 5mm inner diameter is the mounting hole, so check that your shaft, bolt or axle matches before ordering. Outer diameter and width: at 18mm across and 8.5mm wide, the pulley is compact enough for tight belt paths. Bearings: two bearings per pulley mean the idler turns on its own bearings rather than sliding on a fixed surface. Material and weight: aluminium construction keeps each pulley around 6g.

Compatibility and Requirements

These idlers are made for 6mm wide GT2 timing belts and a 5mm bore mounting. They are idler pulleys, used for guiding and tensioning a belt, and pair naturally with 20-tooth GT2 driving pulleys in the same belt system. You will need a suitable 5mm shaft, bolt or axle and a way to secure it in your frame. No other hardware is supplied.

Typical Uses

Common applications include 3D printer belt paths, DIY CNC and motion projects, and other builds where a GT2 belt needs a smooth turning idler. Builders who previously used printed idler wheels often switch to a metal pulley like this for a more consistent running surface.

What's in the Box

  • 2 x Two Trees Aluminum GT2 Timing Idler Pulley, 20 tooth, 5mm bore

Quick specs

Item Type
Timing Pulley
Compatibility
for 6mm belt, 6mm Belt
Material
Aluminium
Inner Diameter (mm)
5
Outer Diameter (mm)
18
No. of Teeth
20
See all specifications