Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 10K Ohm single turn SMD trimmer potentiometer in a compact 3x3 mm surface mount package for on-board resistance adjustment. It lets you calibrate and fine-tune circuits with about 250 degrees of mechanical rotation.

Key Highlights

  • 10K Ohm resistance value with 20 percent tolerance
  • Compact 3x3 mm SMD body for dense PCB layouts
  • Single turn adjustment across a nominal 250 degree mechanical angle
  • ±150 ppm per degree Celsius temperature coefficient
  • Operates from -55 to 125 degrees Celsius
  • Approximately 0.1 g per unit for easy parts stocking

Ideal For

  • Electronics hobbyists building and tuning prototype boards
  • Repair technicians replacing surface mount trimmers
  • Instrumentation designers needing compact calibration parts
  • Students learning SMD soldering and circuit adjustment
  • Makers stocking common resistance values in parts kits

Buying Tip

Check that your board uses surface mount pads and confirm the physical footprint against the 3 mm by 3 mm body before ordering.

Elecvora expert review

Our verdict

A practical, low-cost trimmer for boards that only need a single turn of adjustment. Its small 3x3 mm body and wide temperature range make it easy to fit into compact designs.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Compact 3x3 mm SMD footprint
  • Wide -55 to 125 degrees Celsius operating range
  • Single turn adjustment is quick to set
  • Lightweight and easy to stock

Cons

  • 20 percent tolerance limits precision without measuring
  • Single turn offers less fine resolution than multi-turn types
  • Requires SMD soldering equipment

Best for

Compact boards needing quick one-turn calibration

Not ideal for

Applications requiring fine multi-turn adjustment precision

Specifications

Resistance (Ohm)10K
Tolerance (%)20
Temperature Coefficient±150ppm/℃
Operating Temperature (°C)-55 to 125
Mounting TypeSMD/SMT
Mechanical Angle250° (nominal)
Length (mm)3
Width (mm)3
Weight (g)0.1 (approx) (each)
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

Frequently Asked Questions

What is this trimmer used for?
It adjusts resistance on a circuit board for calibration and tuning, such as setting bias or reference levels.
Is it through-hole or surface mount?
It is a surface mount (SMD/SMT) component, so it is soldered to PCB pads rather than through holes.
How precise is the adjustment?
The single turn design covers the range in about 250 degrees of rotation, and the nominal resistance carries a 20 percent tolerance.
What temperature range does it handle?
It is rated for operation from -55 to 125 degrees Celsius.
What is included with the purchase?
Package contents are not specified in the product data, so confirm the quantity and included items before ordering.
How should I store spare units?
Keep them in a dry, static-safe container and handle with care, since each unit weighs only about 0.1 g.

Overview

This 10K Ohm SMD single turn trimmer potentiometer is a small surface mount component used to adjust resistance on a circuit board during calibration or tuning. The single turn design means the full resistance range is covered within a nominal 250 degree mechanical angle, so a small screwdriver adjustment gives a quick, direct setting. With a body measuring just 3 mm by 3 mm, it fits into compact layouts where larger trimmers are impractical.

Key Features

  • 10K Ohm resistance for common divider, bias and calibration networks
  • Surface mount (SMD/SMT) mounting for reflow soldering onto PCB pads
  • Single turn adjustment with a nominal 250 degree mechanical angle
  • 20 percent tolerance on the nominal resistance value
  • Temperature coefficient of ±150 ppm per degree Celsius for predictable drift
  • Wide operating range from -55 to 125 degrees Celsius
  • Lightweight at approximately 0.1 g per unit

Specifications Explained

The 10K Ohm value is a widely used mid-range resistance, useful where you need a moderate adjustment window rather than a very low or very high value. A 20 percent tolerance means the actual end-to-end resistance can differ from the nominal figure, so measure the part if your circuit needs a precise starting point.

The ±150 ppm per degree Celsius temperature coefficient describes how much the resistance may shift as temperature changes. In practice this is a modest drift figure, which helps when the trimmer sits in equipment that warms up during use. The -55 to 125 degrees Celsius operating range covers typical indoor electronics and many industrial environments.

Because this is a single turn trimmer, the wiper travels from one end of the resistance track to the other in about 250 degrees of rotation. That makes it fast to set but less precise than a multi-turn type, so it suits applications where one turn of resolution is enough. The SMD/SMT mounting means the part is soldered flat to the board rather than through holes.

Compatibility and Requirements

This trimmer requires a PCB with matching surface mount pads and a suitable reflow soldering process. Adjustment is made with a small trimming tool or screwdriver. No additional hardware is supplied with the component.

Typical Uses

Single turn SMD trimmers like this are commonly used for calibration and tuning where a one-turn adjustment is sufficient. Typical roles include setting reference levels, trimming bias points, balancing sensor circuits and making small resistance corrections in prototype or production boards.

What's in the Box

Package contents are not specified for this listing. Please confirm the quantity and included items before ordering.

Quick specs

Resistance (Ohm)
10K
Tolerance (%)
20
Temperature Coefficient
±150ppm/℃
Operating Temperature (°C)
-55 to 125
Mounting Type
SMD/SMT
Mechanical Angle
250° (nominal)
See all specifications