Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 100k ohm 3386P through-hole trimpot that lets you preset and fine-tune resistance on a PCB with a screwdriver. Its single-turn design and 9.5 × 9.5 mm footprint make it a simple fit for calibration and bias adjustments.

Key Highlights

  • 100k ohm resistance with 10% tolerance for preset adjustment
  • Single-turn screwdriver adjustment for quick, repeatable setting
  • Through-hole mounting for secure PCB installation
  • Compact 9.5 × 9.5 mm body fits dense board layouts
  • Stable ±100ppm/°C temperature coefficient
  • Operates from -55 to 125°C for demanding environments

Ideal For

  • Hobbyists building and calibrating analogue circuits
  • Repair technicians replacing preset resistors
  • Design engineers prototyping PCB layouts
  • Students learning through-hole assembly
  • Makers building test fixtures and sensor boards

Buying Tip

Check that your PCB footprint matches the 3386P through-hole lead spacing and confirm you need a single-turn rather than multi-turn adjustment before ordering.

Elecvora expert review

Our verdict

A straightforward through-hole trimpot that does one job well: letting you set and adjust a 100k ohm preset value on a board. It is a sensible consumable for calibration and prototyping work.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Common 100k ohm value suits many bias and reference circuits
  • Single-turn adjustment is quick to set
  • Compact 9.5 × 9.5 mm footprint
  • Wide -55 to 125°C operating range

Cons

  • Single-turn design offers less fine resolution than multi-turn types
  • Requires soldering and a separate screwdriver for adjustment
  • Brand marking may vary between units

Best for

General-purpose PCB preset and calibration work

Not ideal for

Precision multi-turn trimming where very fine resolution is required

Specifications

Resistance (Ohm)100k
Tolerance (%)10
Temperature Coefficient±100ppm/℃
Operating Temperature (°C)-55 to 125
Mounting TypeThrough Hole
Length (mm)9.5
Width (mm)9.5
Weight (g)0.1 (approx) (each)
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

What's in the box

  • 1 x 3386P 100k Ohm Trimpot Trimmer Potentiometer

Frequently Asked Questions

What is a trimpot used for?
A trimpot is a small adjustable resistor used to set a preset value in a circuit, such as a bias point or reference voltage. It is adjusted with a screwdriver and then usually left in place.
How do I adjust this potentiometer?
Turn the screw slot with a small flat-blade screwdriver. This is a single-turn part, so the full adjustment range is covered in one rotation.
Does it come with a knob or shaft?
No. This is a preset trimmer adjusted with a screwdriver, not a panel-mounted potentiometer with a shaft and knob.
What is included in the package?
One 3386P 100k ohm trimpot trimmer potentiometer is included. No other parts or tools are supplied.
Can it be used at high temperatures?
It is rated for operation from -55 to 125°C, so it can be used in circuits that run warm within that range.
How should I store it?
Keep it in a dry place away from mechanical stress on the leads. Handle by the body rather than bending the leads repeatedly.

Overview

The Generic 3386P is a 100k ohm trimmer potentiometer designed for through-hole mounting on printed circuit boards. It gives you a simple way to set a preset resistance value and adjust it later with a screwdriver, making it useful during calibration, prototyping and repair work. The single-turn mechanism changes resistance across one rotation, so you can move quickly to a target value without counting turns.

Key Features

  • 100k ohm resistance: a common value for bias, reference and calibration circuits.
  • Single-turn adjustment: a screwdriver slot lets you set the wiper position directly.
  • Through-hole mounting: leads pass through the PCB for a mechanically secure joint.
  • Compact square body: 9.5 mm by 9.5 mm, suitable for tight board areas.
  • Wide operating range: rated for -55 to 125°C.
  • Lightweight: approximately 0.1 g per unit.

Specifications Explained

The 100k ohm resistance is the total end-to-end value of the element. The wiper divides this value, so the resistance between the wiper and either end changes as you turn the screw. A 10% tolerance means the actual end-to-end value can sit within a small band around 100k ohm, which is normal for preset trimmers and usually acceptable where the circuit is adjusted after assembly.

The ±100ppm/°C temperature coefficient describes how much the resistance drifts as temperature changes. Lower drift is better for stable settings, and this figure is a reasonable match for general-purpose calibration. The -55 to 125°C operating range covers most indoor and many industrial environments. Through-hole mounting is the key mechanical detail: the part is soldered into plated holes rather than placed on the surface, which suits hand assembly and rework.

Compatibility and Requirements

This trimpot requires a PCB with through-holes spaced to match its lead pattern and a soldering method suitable for through-hole components. Adjustment requires a small flat-blade screwdriver. No other accessories are included.

Typical Uses

  • Setting bias and offset in analogue circuits
  • Calibrating sensor and reference voltages
  • Prototype and breadboard-to-PCB builds
  • Repair and replacement of preset resistors
  • Test fixtures and educational projects

What's in the Box

One 3386P 100k ohm trimpot trimmer potentiometer. The brand printed on the part may vary.

Quick specs

Resistance (Ohm)
100k
Tolerance (%)
10
Temperature Coefficient
±100ppm/℃
Operating Temperature (°C)
-55 to 125
Mounting Type
Through Hole
Length (mm)
9.5
See all specifications