Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A ready-built board that converts 4-20mA or 0-20mA industrial sensor current into a 0-3.3V, 0-5V or 0-10V analog voltage for your microcontroller's ADC pin. Screw terminals and onboard zero/span trimmers remove the need to design and tune your own conversion circuit.

Key Highlights

  • Accepts 4-20mA and 0-20mA current inputs
  • Jumper-selectable 0-3.3V, 0-5V and 0-10V outputs
  • Onboard zero and span potentiometers for calibration
  • Screw terminal connectors for simple wiring
  • Wide 7-36V supply with reverse-polarity protection
  • Precision sampling resistor for stable, linear readings

Ideal For

  • Makers integrating industrial sensors with Arduino or Raspberry Pi
  • Engineering students learning current-loop instrumentation
  • Prototypers building data acquisition setups
  • Technicians testing 4-20mA transmitters on the bench
  • Hobbyists adding industrial-grade sensing to projects

Buying Tip

Check your microcontroller's ADC input limit and your power supply voltage first, since a 10V output requires a supply above 12V.

Elecvora expert review

Our verdict

A practical, low-cost way to bring current-loop sensors into a microcontroller project without designing your own conversion circuit. The adjustable zero and span plus selectable output ranges cover most common needs.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Handles both 4-20mA and 0-20mA inputs
  • Three selectable output voltage ranges
  • Screw terminals simplify wiring
  • Reverse-polarity protection adds durability
  • Compact and lightweight

Cons

  • Requires a separate 7-36V supply
  • Manual zero and span calibration needed
  • 10V output needs a supply above 12V

Best for

Makers and students interfacing 4-20mA industrial sensors with Arduino or Raspberry Pi

Not ideal for

Users wanting a fully digital or plug-and-play USB sensor interface

Specifications

Model No. / NameConverter
Input current4-20Ma & 0-20mA
Output Voltage0-3.3V 0-5V 0-10V
Weight (g)12
Shipping Weight0.02 kg
Shipping Dimensions6 × 5 × 3 cm

Frequently Asked Questions

What input signals does this board accept?
It accepts 4-20mA and 0-20mA current signals, the two common industrial current-loop standards.
What output voltages can I select?
You can set the output to 0-3.3V, 0-5V or 0-10V using the jumper caps on J1.
What power supply does it need?
The board runs from 7-36V DC. For a 10V output, the supply voltage must be greater than 12V.
How do I calibrate it?
Apply the minimum current and adjust the ZERO trimmer, then apply 20mA and adjust the SPAN trimmer until the output matches your target voltage.
Can I connect it directly to an Arduino?
Yes. The analog output connects to an ADC pin on Arduino, Raspberry Pi or another microcontroller.
What happens if I reverse the power wiring?
The board has reverse-polarity protection, so reversing the supply does not burn it out.

Overview

Industrial transmitters usually communicate through a 4-20mA current loop, while microcontrollers read voltage on their ADC pins. This converter board sits between the two and does the translation for you. Feed it a 4-20mA or 0-20mA signal and it produces a proportional analog voltage that connects directly to an Arduino, Raspberry Pi or any other microcontroller with an analog input.

The board is assembled and ready to wire. Screw terminals hold the current input and voltage output, and two trimmers let you set the zero point and the span so the output matches your chosen range. Because the heavy lifting is already done, you avoid designing, building and tuning an external op-amp circuit.

Key Features

  • Works with both 4-20mA and 0-20mA current signals
  • Selectable output ranges of 0-3.3V, 0-5V and 0-10V via jumper caps
  • Zero and span potentiometers for adjusting the low and high ends
  • Onboard screw terminals for input and output wiring
  • Reverse-polarity protection so an accidental swap does not damage the board
  • High-precision, low temperature-drift sampling resistor for good linearity

Specifications Explained

Input current

The board reads either a 4-20mA loop or a 0-20mA signal, covering the two most common industrial current standards. The 4-20mA mode is useful because the live zero at 4mA helps distinguish a real minimum reading from a broken wire.

Output voltage

You choose the output range with the jumper caps: 0-3.3V for 3.3V logic boards, 0-5V for classic 5V Arduino boards, or 0-10V for equipment that expects a higher analog level. Match the range to your ADC's input limit before connecting.

Supply voltage

The module runs from 7-36V. If you want a 10V output, the supply must be above 12V, so plan your power source with that in mind.

Size and weight

At roughly 12g and shipped in a 6 x 5 x 3 cm package, the board is small enough to tuck into an enclosure or project box.

Compatibility and Requirements

The board is intended for microcontrollers with an analog-to-digital converter, such as Arduino or Raspberry Pi boards. You supply a 7-36V DC source, and for 10V output the supply must exceed 12V. Wiring is done through the onboard screw terminals, and the output range is set with the jumper caps. No specific software library is required; you simply read the analog pin.

Typical Uses

  • Reading industrial pressure, flow or level transmitters with a microcontroller
  • Bringing 4-20mA sensors into student and hobby projects
  • Prototyping data acquisition for current-loop devices
  • Testing and calibrating sensors on the bench

Quick specs

Model No. / Name
Converter
Input current
4-20Ma & 0-20mA
Output Voltage
0-3.3V 0-5V 0-10V
Weight (g)
12
Shipping Weight
0.02 kg
Shipping Dimensions
6 × 5 × 3 cm
See all specifications