
1 / 5 · Click to enlarge
AI Summary
A 750KV outrunner motor for multirotors using 14–16 inch propellers, rated for 2S–6S LiPO and 20–40A ESCs. It delivers up to 1500 g thrust at 4S with a 4 mm shaft and 112 g body.
Key Highlights
- 750 KV high-torque winding for large-prop lift builds
- Rated for 2S to 6S LiPO with a 20 to 40A ESC
- Up to 1500 g thrust at 4S
- 4 mm shaft pairs with 14 to 16 inch propellers
- Fan-style cooling holes and 140°C rated winding wire
- Rear mounting holes at 16 mm and 19 mm spacing
Ideal For
- Builders of large multirotor frames using 14–16 inch props
- Aerial photography and payload-carrying UAV projects
- Long-endurance drone platforms needing torque over RPM
- Makers prototyping custom UAV and RC builds
- Hobbyists upgrading motors on compatible arms and mounts
Buying Tip
Check that your frame arm matches the 16 mm or 19 mm rear mounting hole spacing and that your prop mount fits the 4 mm shaft before ordering.
Elecvora expert review
Our verdict
A solid, no-frills outrunner for builders who need torque for large props at a modest weight. Its clear voltage, ESC and prop ranges make it easy to plan a build around, though you will need to solder connectors and match the mount yourself.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 750 KV winding suits 14 to 16 inch propellers
- Broad 2S to 6S LiPO range with a defined 20 to 40A ESC window
- Up to 1500 g thrust at 4S
- Cooling holes, high-temperature wire and epoxy-coated plates
- Includes connectors and a propeller mount
Cons
- Connectors must be soldered to the motor leads
- Battery, ESC and propeller are not included
- Only 16 mm and 19 mm mounting patterns are supported
Best for
Multirotor and UAV builds using 14–16 inch props that prioritise torque and lift
Not ideal for
Small high-RPM racing quads or builds needing a different mounting pattern
Specifications
| Motor KV (RPM/V) | 750 KV |
|---|---|
| Motor Type | Brushless Motor |
| Compatible LiPO Batteries | 2S to 6S |
| Required ESC (A) | 20 ~ 40 |
| Maximum Thrust (gm) | 1500@4S |
| Shaft Diameter | 4 mm |
| Compatible Prop (inch) | 14 ~ 16 |
| Length (mm) | 50 |
| Width (mm) | 50 |
| Weight (g) | 112 |
| Shipping Weight | 0.12 kg |
| Shipping Dimensions | 5 × 4 × 2 cm |
What's in the box
- 1 x 5010 750KV high torque brushless motor
- 3 x male-female golden connector pairs with heat shrink tube
- 1 x propeller mount with accessories
Frequently Asked Questions
What battery should I use with this motor?
Which propellers fit this motor?
What ESC do I need?
How much thrust does it produce?
What is included with the motor?
How do I mount it to my frame?
Overview
The Generic 5010 750KV is a brushless outrunner motor aimed at drone builders who need torque rather than raw RPM. With a 50 mm class stator, a 4 mm shaft and a 112 g body, it is sized to spin 14 to 16 inch propellers and is rated for 2S to 6S LiPO packs through a 20 to 40A ESC. At 4S it can produce up to 1500 g of thrust per motor, which makes it a sensible starting point for multirotor frames where lift and endurance matter more than snap throttle response.
Key Features
- High-torque 750 KV winding tuned for larger props and steady thrust.
- NdFeB magnets with a high temperature rating for consistent operation.
- 140°C rated winding wire to reduce the risk of insulation damage under load.
- Four fan-style cooling holes that push air through the motor as it spins.
- Epoxy-coated inner plates that help prevent winding shorts.
- Lubricated ball bearings supporting smooth rotation.
- High-temperature adhesive securing the stator windings against shifting.
- Dual mounting patterns at 16 mm and 19 mm hole spacing.
Specifications Explained
750 KV means the motor turns roughly 750 RPM per volt applied, so a 4S pack gives a moderate, controllable prop speed that suits 14 to 16 inch blades. 2S to 6S LiPO compatibility lets you choose a lower voltage for gentler setups or a higher one for more thrust, provided the propeller and ESC stay within their limits. 20 to 40A ESC is the current window the motor expects; pick an ESC rated inside that band and matched to your prop load. The 4 mm shaft sets the prop mount and adapter you need, while the 1500 g thrust at 4S figure is a useful reference point when estimating total lift for a multirotor.
Compatibility and Requirements
Use a 2S to 6S LiPO battery and a 20 to 40A ESC. Pair the motor with 14 to 16 inch propellers and confirm the shaft and prop mount match your chosen prop. The rear mounting holes are spaced at 16 mm and 19 mm, so check your frame or motor mount before installation. The package includes a propeller mount with accessories and three male-female golden connector pairs with heat shrink tube for wiring.
Typical Uses
This motor suits multirotor builds that carry cameras, sensors or payloads, long-endurance aerial platforms, and larger frames where 14 to 16 inch props are part of the design. It is also a reasonable option for workshop projects and UAV prototypes that need a torque-focused outrunner.
What's in the Box
- 1 x 5010 750KV high torque brushless motor
- 3 x male-female golden connector pairs with heat shrink tube
- 1 x propeller mount with accessories
Quick specs
- Motor KV (RPM/V)
- 750 KV
- Motor Type
- Brushless Motor
- Compatible LiPO Batteries
- 2S to 6S
- Required ESC (A)
- 20 ~ 40
- Maximum Thrust (gm)
- 1500@4S
- Shaft Diameter
- 4 mm
















